manualshive.com logo in svg
background image

 

 

7

When programmed as Enabled: The windows will be closed automatically when 
pressing button 1 or 1+2 to arm the system. With the feature enabled, the CH3 
output will be unable to be operated by remote control.   

When programmed as Disabled: The channel 3 output will be activated as long as pressing and 

holding buttons 1+3 for 1 second. 
 

 
C) Remote Transmitter Code Learning 
The included remotes control are programmed to the system before they leave the factory. 
Follow the below procedure to program a new remote control:   

a> Follow the below procedure to program a new remote control. 
With the alarm disarmed, and the doors CLOSED, switch the ignition ON/OFF 3 times (within 1 

second of each other) and then back to the ON position.  
The siren will sound for 2 seconds to indicate the alarm is in code learning mode. 

b> To program the new remote control press button (1) within 10 seconds. 
The siren will chirp and the hazard lights flash twice to confirm that the code has 

been learned.  Follow the same procedure for second, third and fourth remote transmitter. 
c> If the ignition is turned OFF or button (1) is not pressed within 10 seconds, the system will 

quit the code-learning mode. If this happens you must start again from the first step. 
d> Up to 4 remote control transmitters can be programmed to the system.   

 
 

D) Installation Notes 
 

D-1) Ignition 2 Connection 

If a vehicle has ignition 2 (ACC 2), the yellow/black wire (C4-2) must be connected to Ignition 2 
(ACC 2) via a 30A relay as shown below. 

 

C4-2 (-)

Ignition 2

+12V

86

87

30

87A

85

+12V

 

 

Important:

  This  wire  must  be  connected  to  Ignition  2  (ACC  2)  in  the  vehicle.    Or  it  will  affect 

performance of remote engine start. 
 

 

D-2) Installation without Remote Starter Features 

If the remote starter and turbo timer features are not required, the following wires do not need 

to be connected: 
 

C1-2Yellow/Green To Ignition Start 
C1-3Blue/WhiteTo Ignition Acc 

C3-5Black/RedTo handbrake light 
C4-1Green To RPM 

C4-2Yellow/BlackTo ignition 2 
C4-3Red/BlackTo alternator 

 

Содержание Predator EVO4+2












Отзывы: