SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
31
18 To Remove the Oven Door Seal
a) Open oven door. The seal is held in place by small
hooks on the rear face. At the corner pull seal
diagonally away from the door centre until that hook is
released.
b) Proceed to the next hook and release it in a similar
way, and so on. Use force if the hooks are stiff, as the
old seal will be discarded.
c) When fitting new seal, position the seal join at the
bottom. Hook the new seal in one of the corner holes
of the door, and proceed round the door snapping in
each hook in turn.
19 To Adjust the Oven Door Catch Keeper
a) Open the oven door and slacken the locknut at the
keeper base.
b) Adjust the keeper inward or outward as required, until
the desired door operation is obtained.
c) Re-tighten the locknut.
20 To Remove the Hotplate Spark Generator
Disconnect the appliance from the electricity supply.
a) Pull the unit forward to access the cover boxes at the
appliance rear. Remove the fixings that secure the
cover and lift it clear.
b) Undo the terminal connections noting their positions.
c) Undo the fixings that secure the spark generator and
remove the device.
21 To Remove the Hotplate Electrode Leads
Disconnect from the electricity supply.
Pull the unit forward to access the rear of the appliance.
a) Remove the pan supports, hotplate accessories and
burner heads.
b) Remove the hotplate as detailed in Section 2.
c) Remove the cover box and disconnect all HT leads at
the generator.
d) Remove the lower back panel and disconnect the lead
at the electrode.
e) Pull the sleeved bundle of HT leads up through the
rear upright.
f) Pull the appropriate lead from the sleeve and push in
the replacement.
g) Replace the leads in the rear upright.
h) Re-connect the leads at the generator and oven
electrode.
j) Re-assemble in reverse order and check ignition.
22 To Remove Oven Inner Back
a) Open the oven door. For the LH oven unscrew the 2
thermostat phial fixing screws. Remove the fixings that
secure the inner back to the oven rear.
b) Lift the removable panel away.
c) Re-assemble in reverse order. Ensure that the retaining
fixings are fully tightened.
23 To Replace an Oven Fan
Disconnect the appliance from the electricity supply.
a) Pull the unit forward to access the cover boxes at the
rear of the appliance. Remove the fixings that secure
the cover and lift it clear.
b) Remove the fan wiring, noting the connection
positions.
c) Remove the inner back as detailed in Section 22.
d) Hold the fan blades and undo the centre nut (LH
thread), brass washers, fan blade and circlip.
e) Undo the fixings that retain the fan and remove it from
the cavity rear.
f) Fit the replacement and re-assemble parts in reverse
order. Check that the oven operates satisfactorily.
25 To Remove an Oven fan Element
Disconnect the appliance from the electricity supply.
a) Remove oven inner back (see 22).
b) Remove 2 screws from the top of the element and 1
from the bottom of the element in side the oven.
c) Lift element out carefully, disconnect the terminals
connected to the element noting their positions. If
it is not possible to disconnect the leads in this way,
pull cooker forward to gain access to the rear, remove
screws securing the electric cover to the back sheet
and remove cover and disconnect the terminals from
the rear.
d) Fit new element, and reassemble in reverse order.
e) Check that the oven operates correctly.
26 To Remove the LH Oven Bottom and Top
Elements
Disconnect the appliance from the electricity supply.
Bottom Element
a) Pull the unit forward to access the cover boxes at the
rear of the unit. Remove the fixings that secure the
cover and lift it clear.
b) Undo the terminal connections, noting their positions.
c) Remove the fixings that secure the bottom element
cover.
d) Undo the terminal connections, noting their positions.
e) Remove the lower element support fixings.
f) Remove the element bracket fixings and withdraw
element.
g) Replace the element and re-assemble parts in reverse
order.
Top Element
a) Open the LH oven door and undo the fixings that
secure the heat shield.
b) Remove the top element bracket fixings and withdraw
element.
