background image

FTP Series Programmable DC Power Supply Operation Manual

____________________________________________________________________________

- 2 -

Safety Abstract

Please observe important safety instructions strictly in the process of operating and using the power supply. Not
observing safety precautions or warnings in this manual will probably weaken protective functions provided by
the power supply. Faithtech will not assume any liability for damages if the user does not observe those safety
precautions.

Important Safety Instructions

Ensure proper grounding

. Before turning on the power supply, please make sure that the power supply

is reliably grounded to prevent electric shock.

Single phase 220VAC input

. Make sure the input wire meets the specified standards, and a protective

cover must be installed to prevent electric shock.

Output cable connection

. Make sure the output wire meets the specified standards, and a protective

cover must be installed to prevent electric shock.

Do not open the instrument case

. Operators are not allowed to open the shell of the power supply.

Non-professionals are not allowed to repair or adjust.

Do not

use in a hazardous or dangerous manner

either alone or in conjunction with other equipment.

Operating in inflammable or explosive environment is strictly forbidden.

Safety Symbols

Please see the following table for meanings of international symbols applied in the mainframe or the user’s
manual.
----------------------------------------------------------------------------------------------------------------------

WARNING

: To avoid injury, death of personnel, or damage to the instrument, the operator

must refer to the explanation in the instruction manual.

----------------------------------------------------------------------------------------------------------------------

High temperature

: This symbol indicates the temperature is hazardous to human beings.

Do not touch it to avoid any personal injury.

----------------------------------------------------------------------------------------------------------------------

DANGER

: High voltage.

---------------------------------------------------------------------------------------------------------------------

Protective grounding terminal

: This symbol indicates that the terminal must be

connected to ground before operation of the equipment to protect against electrical
shock in case of a fault.

----------------------------------------------------------------------------------------------------------------------

Содержание FTP Series




















































Отзывы: