background image

13

APPROvED FUEL TYPES

EndURancE 50F   

APPROvED FUEL TYPES

Corn, Wheat and Grain

Shelled corn, wheat and grain pellets must have 

16% or less moisture content. The keys to satisfac-

tory performance are proper operation of the fur-

nace, diligent maintenance, and burning only dry, 

clean, quality fuel. These fuels must be screened to 

remove dust prior to using.

clinkers and ash are by-products of burning biomass fuels and 

are not caused by your furnace. Furnace performance is re-

duced if poor quality fuel is used. Using a thermostat will cause 

variations in the maintenance. check the burn pot frequently 

in the beginning to establish a maintenance schedule based 

on fuel use and burn rates. contact your dealer for more infor-

mation on where to get high quality biomass fuels to burn in 

your furnace. Store fuel in an air tight container or use other 

methods to ensure they do not become rain soaked or absorb 

moisture from damp or wet floors. This will also prevent rodents 

from becoming a problem. do not store fuel within furnace in-

stallation clearance areas or within the space required for ash 

removal. The 50F furnace is not warranted against damage 

caused by poor quality fuel, incorrect operation, poor mainte-

nance or incorrect installation.

Wood Pellets and Cherry Pits

contact your dealer for more information on aPFI approved 

wood pellet fuels. no standard exists for cherry pits.

 
Fuel Type:

1.  High ash 

2.  L Wheat
3.  Wheat

4.  HM corn
5.  corn
6.  LM corn
7.  cherry Pit
8.  LG Pellet
9.  S Pellet
10.  P Pellet

Fuel Description:

High ash = any High ash Fuel

L Wheat = Lower Wheat
Wheat = Normal Wheat

HM corn = High Moisture corn (16 - 14%)
corn = normal corn (15 - 13%)
LM corn = Low Moisture corn (14 - 12%)
cherry Pit = cherry Pits
LG Pellet = Low Grade Pellets
S Pellet = Standard Pellets
P Pellet = Premium Pellets

NOTE: Excessive grain dust must  

be screened by sifting with mesh 

screening. Large pieces of cob  

may plug the auger.

NOTE: This furnace is approved only for corn, wood and grain pellets, wheat and cherry pits.

Fuel Selection Screen

Содержание Endurance 50F





































Отзывы: