1 2 3 4 5 6 7 8 9 10
11 12 13 14 15
16 17 18 19 20 21
A
B A
B
9
COMMON
OPEN
CLOSE
RADIO
LED 24 V - 3 W max
STOP
T1
MOTOR RUN TIME
1 s - 22 s
T2
DWELL TIME
1 s - 180 s
L1
L6
L7
L3
L8
L4
L5
L2
L9
L10
L11
Secondary
fuse
transformer
F4 = 2A
Primary
fuse
transformer
F3 = 630 mA
Electric valve fuse,
acoustic device, flashing light
and led F5 = 2 A
Motor fuse M2
F2 = 5 A
Motor fuse M1
F1 = 5 A
COMMON
M1
M2
COMMON
Red
Yellow
Green
Input P
57 58
63 64 65 66 60 61
24 Vdc output
+
-
55 56
TRANSFORMER
1
2
COMMON
LIMIT
SWITCH
OPEN
M1
(Bollard
in
down position)
LIMIT
SWITCH
OPEN
M2
(Bollard
in
down position)
LIMIT
SWITCH
C
LOSE
M1
(Bollard
in
up
position)
LIMIT
SWITCH
C
LOSE M2
(Bollard
in
up
position)
Pedestrian
opening
connection
motor
bollard M1
PHOTOCELLS OR
MAGNETIC
LOOP
OUTPUT 24
V -
250 mA
for max charge:
- n° 2
pairs
of photocells
- n°
1
radio
receiver
MOTOR M1
Bollard
n°
1
MOTOR M2
Bollard
n°
2
NEUTRAL
LIVE
N
F
Anti-disturbance filter
COMMON
Elpro S20
STRIP jumper
LIMIT SWITCH
ELPRO S20
Capacitor 20 µF
M1
20 VA - 50/60 Hz
23
22
24 25
Capacitor 20 µF
M2
RADIO
PLUG-IN CARD
CONNECTOR
LIMIT SWITCH DIAGNOSTIC
230 V - 50 Hz
POWER
SUPPLY
STABILIZER
FOR
SOLENOID
VALVE
POWER
SUPPLY
230 V ±10% 50
Hz
SINGLE-PHASE
R
ed
FLASHING LIGHT
230
V - 100
W max
SIGNAL LIGHT
230
V - 100
W max
Fuse 1 A
PLUG-IN CONNECTOR FOR
3-LAMP TRAFFIC LIGHTS
MAX100 W EACH LAMP
Yello
w
Gr
een
C
ommon
Po
w
er supply
230
V - 50 H
z
(
Optional:
plug-in PCB for traffic
light to suit 230 V lamp)
code
7282L
Coral, Vigilo, Talos, Talos M30, Strabuc 930 Opinat
range of bollards with limit switch: with the STRIP jumper inserted (as in the picture), Elpro S20
checks cyclicly every 10 minutes that the closing limit switches (post raised) are in the correct position; should any of them fail to be such, only the
motor of the post not in position is operated until this is fully up as required.
Note well:
whenever
Elpro
S20 is re-powered, wait 10 seconds for the logic to become fully operating again.
The electronic control panel Elpro S20 is designed to operate the Talos, Talos M30, Strabuc 930 Opinat, Coral and Vigilo; power supply is
230 V single-phase.
Elpro S20 is capable of monitoring damages or malfunctioning with the system (ISC).
I.S.C.
=
I
ntegrity and
S
upervision
C
ircuit, is a special function of Elpro S20 which can self control the electronic PCB and detect any damages
occurring with any components or accessories. In this case, provided that the post is fitted with a release electric valve, lowering is allowed
automatically. The manufacturing company declines any responsability for incorrect handling and application; also, it reserves the right to
change or update the control panel any time.
IMPORTANT FOR THE INSTALLATION AND THE CORRECT FUNCTIONING:
- The control box must be installed in a dry and sheltered place; suitable holes are provided with the FADINI universal box for fitting
purpose and in case any commercial box is used, this must be adequate to the job.
- Make sure that power supply to the control board be 230 V ±10%.
- Make sure that power supply to the electric motor be 230 V ±10%.
- For distances longer than 50 metres increase the section of the wires.
- Fit the mains to the control box with a high sensitivity, 0,03 A, differential, magnetic-thermal circuit breaker.
- Cables with 1,5 mm² section wires are to be used for the power supply, electric motor and flasher for distances up to 50 m.
- Cables with 1 mm² section wires are to be used for the limit switches, photocells, push buttons and accessories.
N.W.: for applications such as light switching, CCTV, etc. use solid state relays to prevent the microprocessor from being affected.
IN CASE OF FAILURE OF THE PANEL:
- Check the electronic PCB voltage supply is 230 V ±10%.
- Check the electric motor power supply is 230 V ±10%.
- For longer distances increase wire section.
- Check fuses.
- The photocell contacts are closed.
- Check all NC contacts.
- The limit switches are properly connected and work correctly.
- In case the electric valve is fitted, check integrity with all fuses.
- Check that no voltage drop has occurred from the control board to the electric motor.
ON
OFF
1 2 3 4 5 6 7 8 9 10 11 12
52
51
53
SYMBOLS:
NO
contact
NC
contact
Led
ON
Led
OFF
Pilot light
Flasher
-
+
-
+
GB
Elpro S20
ELECTRONIC CONTROLLER UP TO 2 AUTOMATIC BOLLARDS,
WITH OR WITHOUT LIMIT SWITCH
1
2
1 2
ELPRO S20
ELPRO
S20
VERS.
Содержание Elpro S20
Страница 38: ...Elpro S20 38...
