Factory Five Racing '33 Hot Rod Скачать руководство пользователя страница 349 | Manualshive

Страница: 349 / 710

background image

348

www.factoryfive.com

508-291-3443

Push the ball stud retainer onto the throttle pedal.
While pulling the cable tight, push the accelerator pedal up until it hits the frame and align the ball stud
retainer with the cable.
Mark on the cable where the retainer ends.
Measure ⅜” from the mark on the cable towards the end of the cable and re-mark the cable.
Using a pair of wire cutters, cut the cable at the new location marked.
Remove the ball stud retainer from the accelerator pedal.
Push and twist the ball stud retainer onto the end of the cable and attach the ball stud retainer using a

5

/

64

”

hex key.
Check the full range of the accelerator pedal travel to ensure that there are no interferences with the pedal
or travel.



After driving the car for the first time you may want to adjust the pedal location for optimum

heal/toe and shoe size differences.

Seat Harnesses



¾” wrench, ¾” socket, ratchet



Seat harnesses/fasteners



These have to be installed before the body because the bolt may be difficult to install with the body in

place.



Even if you are not going to install the upper seat harnesses, place the bolt and nut on the chassis as

shown in case you or the next owner decided to install them. This makes is much easier in the future.

The shoulder part of the harness is mounted to the U-shaped bracket above the gas tank.

«
...
347
348
349
350
351
...
»

Содержание '33 Hot Rod







































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для '33 Hot Rod

Бренд: KC HiLiTES Страницы: 4

Бренд: ULTIMATE SPEED Страницы: 19

Бренд: Jeep Страницы: 25

Бренд: Jeep Страницы: 51

Бренд: Farenheit Страницы: 8

Бренд: OEM Tools Страницы: 4

Бренд: Uniden Страницы: 16

Бренд: Uniden Страницы: 20

ESCALADE FAMILY - SPECIFICATIONS 2011

Бренд: Cadillac Страницы: 1

Бренд: Alpine Страницы: 8

Бренд: Yakima Страницы: 12

Бренд: SnapPad Страницы: 5

Quattroporte Automatic

Бренд: Maserati Страницы: 272

Бренд: rockymounts Страницы: 6

Бренд: ORA Страницы: 7

FABIA II TMB PS 035

Бренд: Skoda Страницы: 16

Бренд: TracRac Страницы: 8

Бренд: Rhino-Rack Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды