manualshive.com logo in svg

Factory Five Racing '33 Hot Rod, Инструкция по сборке

Сборка Фабрики Factory Five Racing '33 Hot Rod. Полное руководство по сборке доступно для загрузки бесплатно на manualshive.com. Подробное руководство сборки, инструкции по сборке и эксплуатации включены в сборку. Не упустите шанс собрать свой собственный горячий род в стиле '33!

Поделиться
Скачать
background image

10 

www.factoryfive.com 

508-291-3443 

 

Safety Notice 

While there are many things to love and be proud of in our country today there are a few things that we 
wish were different. With regret and a small amount of resentment we include the following warning and 
statement of non-liability at the advice of men with soft hands and necks the size of pencils. 

 

Motorsports involves the operation of machines and materials near the limits of performance. Racing 
involves an inherent amount of risk. Any decision to proceed in the project of building one’s own racecar 
must be made with the acceptance of personal responsibility. If, while building, driving or racing this 
Factory Five Racing kit, should you become injured or die, it will be the result of your own conscious 
decision and we at Factory Five Racing, Inc., disclaim any responsibility of any kind. 

 

The procedures and recommendations contained in this book are to be used as a guide with the ultimate 
determination of safe construction and race-worthiness to be made by you. If you feel uneasy about 
whether you have the skills to build your own vehicle, DO NOT PROCEED. This project involves 
building a car from the bare frame all the way up to a finished vehicle. It is intended for individuals who 
have the skills and abilities commensurate with the scope of a project of this magnitude. 

 

This kit is only a collection of parts designed for use primarily as a race car. Factory Five Racing does not 
build completed or partially completed vehicles.  You are responsible for ensuring that the vehicle you 
build complies with all Federal, State and local laws regarding its use. Except as may be specified in 
writing, Factory Five makes no warranties, expressed or implied, on the products (parts, or kits) offered for 
sale.  All implied warranties of merchantability and fitness for a particular purpose are expressly 
disclaimed by Factory Five. 

 

While Factory Five products are thoroughly tested under actual race conditions, Factory Five cannot 
control the quality of the installation or application of these products. The products offered for sale are 
true race car components, the installment of which often requires considerable time and fabrication 
skill. Before attempting any installation or assembly, the purchaser should determine the suitability of the 
product for the intended use, the time, and level of skill necessary for correct installation or assembly. 

 

Factory Five does not make any warranty, expressed or implied. Purchaser expressly ASSUMES THE 
RISK of all personal, property and economic injury, damage or loss, either direct or indirect, arising from 
the use, misuse, or failure to determine the appropriate use of any Factory Five product. 

 
 
 
 
 
 
 
 
 
 

Ford and Chevrolet, GM and Cobra are registered trademarks. 

Factory Five Racing, Inc. is not connected to the holders of these marks. 

Содержание '33 Hot Rod







































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для '33 Hot Rod

Federal Signal Corporation 7000 Assembly Instructions Manual preview
7000
Бренд: Federal Signal Corporation Страницы: 13
OEM Tools 22505 Operating Instructions And Parts Manual preview
22505
Бренд: OEM Tools Страницы: 4
Blue Giant STRONGARM RVR303 Installation & Technical Manual preview
STRONGARM RVR303
Бренд: Blue Giant Страницы: 48
Ford FIESTA ST 2019 Supplement Manual preview
FIESTA ST 2019
Бренд: Ford Страницы: 37
Safe Fleet RVS-218627 Instruction Manual preview
RVS-218627
Бренд: Safe Fleet Страницы: 38
Honda 08A28-0J6-800 Installation Instructions Manual preview
08A28-0J6-800
Бренд: Honda Страницы: 32
Renault 2016 Sandero Stepway Handbook preview
2016 Sandero Stepway
Бренд: Renault Страницы: 183
Rago FABRICATION R2223TTUNDM Installation Manual preview
R2223TTUNDM
Бренд: Rago FABRICATION Страницы: 10
TAUBENREUTHER 29-T080301 Quick Start Manual preview
29-T080301
Бренд: TAUBENREUTHER Страницы: 8
Honda 2010 Pilot Technology Reference Manual preview
2010 Pilot
Бренд: Honda Страницы: 20
Kia 2009 Rio Series Owner'S Manual preview
2009 Rio Series
Бренд: Kia Страницы: 219
Nav TV Ford 4” UNI-CAM Manual preview
Ford 4” UNI-CAM
Бренд: Nav TV Страницы: 6
Saab 2007 9-3 Remote Starter Owner'S Manual preview
2007 9-3 Remote Starter
Бренд: Saab Страницы: 304
Cadillac 1999 Escalade Owner'S Manual preview
1999 Escalade
Бренд: Cadillac Страницы: 352
Ford ALCON 1968 Owner'S Manual preview
ALCON 1968
Бренд: Ford Страницы: 52
Ferve F-2024 Operating Instructions Manual preview
F-2024
Бренд: Ferve Страницы: 28
Saab 32 025 907 Installation Instructions Manual preview
32 025 907
Бренд: Saab Страницы: 37
Connects2 CTUPO01 Quick Start Manual preview
CTUPO01
Бренд: Connects2 Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды