Factory Five Racing '33 Hot Rod Скачать руководство пользователя страница 203 | Manualshive

Страница: 203 / 710

background image

202

www.factoryfive.com

508-291-3443

Cut the yellow and white rear turn signal light wires off the turn signal connectors that are for the dash
turn signal switch so that the turn signal lights do not back feed and light the front turn signals when the
brakes are pressed.

Fan Wiring

Follow the directions in the chassis harness instructions

Carbureted Engine

Run the coil wires with the alternator wires and gauge sender wires for use with the coil.

Fuel Injected Engine

Leave the coil and crank wires in the footbox and connect them to the power wires for the EFI harness
according to the EFI harness instructions.
If the EFI harness uses its own wires for the fuel pump, remove the fuse for the fuel pump from the fuse
panel and cut and solder the fuel pump wire from the EFI harness onto the chassis harness wire.



If using a Coyote engine, refer to the available “Coyote Install” instructions.

Alternator

Run the alternator wires along the top of the engine to the alternator.

«
...
201
202
203
204
205
...
»

Содержание '33 Hot Rod







































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для '33 Hot Rod

Бренд: Calira Страницы: 14

Бренд: Vauxhall Страницы: 2

Бренд: DEFA Страницы: 7

Бренд: Prorack Страницы: 15

Бренд: Dometic Страницы: 158

Бренд: Caltrend Страницы: 2

Бренд: Audiovox Страницы: 1

EGR-3PVE-COLOUR

Бренд: EGR Страницы: 28

Бренд: BMW Страницы: 21

Бренд: Jeep Страницы: 380

Бренд: AA Products Страницы: 6

Бренд: UAZ Страницы: 90

Бренд: HAUL MASTER Страницы: 8

Бренд: NavInc Страницы: 6

Denali 1094-0185-15

Бренд: E&G Classics Страницы: 3

Бренд: Metra Electronics Страницы: 2

1995 Cutlass Supreme

Бренд: Oldsmobile Страницы: 340

Бренд: Prorack Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды