Factair F3000 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 20

Factair F3000 Скачать руководство пользователя страница 9

Note: For instructions on reading detector tubes and their safe
disposal, refer to the laminated sheet stored within the tester’s carry
case (also added as an appendix within this manual).

Refer to Appendix 4 within this manual for information converting
detector tube readings to a dewpoint.

(xiv) To restart the tester for a subsequent test, momentarily depress the

ON/OFF button. To switch off the tester, depress and hold the
ON/OFF button for approximately 2.5 seconds.

Note: The tester will automatically switch off, if not used, after a
period of 1 hour.

3.2

Testing high-pressure cylinders

(i)

Turn  on  power  by  pressing  and  holding  the  ON/OFF  button  on the
keypad  for  approximately  2.5  seconds.    The  unit  will  display  the
model and serial number.

Press enter



to confirm the date of the last calibration and the battery condition.

Note: It is recommended that your F3000 is calibrated within a 12-
month period.

(ii)

If the battery condition is OK

Press enter



(iii)

Ensure the system flow control valve is closed then connect a hose
from a regulated high-pressure supply to the air inlet on the tester.
A  high-pressure  regulator  and  hose  assembly,  reference  F3002,  is
available  for  this  purpose.    Ensure  the  cylinder  is  fully  charged  by
reading  the  content  gauge.    (A  partly  discharged  cylinder  can  give
an incorrect water test result.)

Note: Maximum inlet pressure at the tester is 10 bar.

- 7 -

«
...
7
8
9
10
11
...
»

Содержание F3000





















Отзывы:

Нет отзывов