Factair F3000 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 20

Factair F3000 Скачать руководство пользователя страница 3

1

INTRODUCTION

Designed for accuracy and ease of use, the Factair F3000 Safe-Air Tester
is  the  fourth  generation  of  this  market-leading  instrument.  Using  the  unit
to  conduct  monthly  checks  of  the  flow  and  purity  of  compressed-air
breathing systems will ensure compliance to the relevant requirements of
COSHH L5.

With  speed  and  repeatability  as  prime  objectives,  the  need  for  manual
adjustment  of  flow  and  timing  has  been  removed.  Once  the  equipment
has  been  set  up  on  site,  tests  are  carried  out  automatically  and  the
detection parameters of EN12021:1998 met or exceeded.

Simple precautions and attention to the operating instructions will ensure
that the F3000 provides many years trouble-free operation. Please read
this manual fully before operating the unit.

Calibration and Warranty

Safe-Air Testers leave our factory with a 12-month warranty and
calibration certificate. Our standard turnaround on annual calibration is 10
working days providing there is no major damage that requires extensive
rebuild.

Inside the carry case there is a laminated sheet listing the detector tubes
that your Safe-Air Tester is calibrated for and information on how to read
them. Alternative types of tubes may not be used without recalibration of
the instrument by Factair.

The date your tester was last calibrated is shown on the digital display.

Note: It is recommended that your F3000 be calibrated within a 12-month
period.

It is the responsibility of the user of this equipment to ensure that it is
operated and maintained in strict accordance with these instructions. The
Manufacturer and Distributor shall not be liable for any incorrect
measurement or any damages, resulting from negligence or incorrect use.

- 1 -

«
1
2
3
4
5
...
»

Содержание F3000





















Отзывы:

Нет отзывов