Factair F3000 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 20

Factair F3000 Скачать руководство пользователя страница 5

3

OPERATION

3.1

Testing of low-pressure breathing airlines and mobiles

(i)

Turn  on  power  by  pressing  and  holding  the  ON/OFF  button  on the
keypad  for  approximately  2.5  seconds.    The  unit  will  display  the
model and serial number.

Press enter



to confirm the date of the last

calibration and the battery condition.

Note: It is recommended that your F3000 is calibrated within a 12-
month period.

(ii)

If the battery condition is OK

Press enter



(iii)

Ensure the system flow control valve is closed then connect the air
supply from the breathing-air system to the tester via a suitable
hose

Note: Minimum inlet pressure 1.5 bar

Maximum inlet pressure 10 bar.

Press enter



IMPORTANT:  If the unit is overpressurised it will automatically
shut  down  and  display  an  overpressure  warning;  it  will  then
need  to  be  returned  to  the  manufacturer  for  inspection  and
resetting.

Note: The above service is chargeable.

(iv) Adjust the system flow control valve so the normal flow required for

the  face-piece  shows  on  the  flowmeter,  best  achieved  by  raising
beyond  the  set  point  and  lowering  the  flow  so  the  flowmeter  reads
the required value.  (120 litres for half and full masks, often more for
air-fed  visors,  hoods  and  suits;  check  flow  requirements  with  the
appropriate RPE data sheet.)  It is recommended that this flow is left
running for the duration of the test to simulate the conditions of use.
Carry  out  the  odour  test  by  smelling  the  air  exhausted  from  the
sintered outlet above the flowmeter.

- 3 -

«
...
3
4
5
6
7
...
»

Содержание F3000





















Отзывы:

Нет отзывов