Faber MatriX 450/500 III, Руководство по установке

Страница: 12 / 32

Installation manual Matrix 450/500 III and MatriX 450/650 III
12 < < < <
False chimney

Construct the false chimney of non-com-
bustible material in combination with
metal profiles or of masonry/concrete
blocks.

Always use a lintel or reinforcing bars
while bricking the false chimney. They
should not be placed directly on the fire-
place.

Make sure that the fireplace never func-
tions as a load-bearing construction, be-
cause of the expansion of the fireplace
through warmth.
Ventilation
Correct ventilation prevents damaging overheating
of the gas control block and its electronics and also
limits the temperature of the convection air. Use
the (optional) supplied Faber ventilation grids (arti-
cle number A9296400) or a similar alternative with
a minimum free passage of 200cm² per grid, in the
space above the fire, when building the false
chimney. Within the false chimney, an horizontal
screen plate, made of non-combustible material,
must be installed just above the ventilation open-
ings. (see “A” in fig. 1.0).
Installation and finishing

Please note!

Take into account a minimum distance of
2mm due to expansion of the fireplace.

Take into account the thickness of any fin-
ishing layer!
The following points are important for installation
and finishing.
H. = Cover trim (fig. 2.4 and 2.7)
I. = Spacer (fig. 2.4)
J. = Upper flange of the combustion cham-
ber (fig. 2.5).
K. = Spacer / glass support (fig. 2.6)
L. = Spacer / glass support (fig. 2.6)
Method I: Installation WITH the cover trim (fig. 2.2)
Build the false chimney or platform against the
decorative strips “
H ” and the spacers “ I ” (see fig.
2.4 and 2.7).
Method II: Installation WITHOUT the cover trim
(fig. 2.3).
Remove the distance profiles “
I ” (see fig. 2.4).

Please note!
Make sure that the distance profile screws “ I ”
are replaced at the front to ensure that the ap-
pliance is air tight.

Build the platform against the glass sup-
ports “
K ” and “ L ” (see fig. 2.6)

Hold point “ J ” for the height off the plat-
form.
5 Removing glass
5.1 Front glass

Place the suction cups on the glass and
slide frame ”
C ” upwards (fig. 3.0).

See fig. 3.0, number:
1 Slide the glass upwards to release the
bottom from the frame.
2 Now gently pull the bottom towards
you.
3 Take the exposed side towards you
and place the glass in a safe place.
For replacing the glass repeat the steps in reverse
order.

Please note!
Avoid fingerprints on the glass, these are no
longer removable once the fire is used.
5.2 Side glass
For cleaning only it’s not necessary to remove the
side glass.

Remove the front glass (see chapter 5.1).

Remove the glass strip at the top (fig. 3.1
and 3.2).

Place a suction cup and remove the side
glass (fig. 3.3).

To do this, see fig. 3.3, number:
1 Slide the glass upwards to release the
bottom from the frame.
2 Then pull the bottom towards you
and place the flass in a safe place.
For replacing the glass repeat the steps in reverse
order.

Please note!
Avoid fingerprints on the glass, these are no
longer removable once the fire is used.
6 Placing decoration material
It is not permitted to use other or to add more ma-
terial in the combustion chamber.
See the supplied decoration instruction card or
chapter 18:

Divide the glass granulate on the perfo-
rated bottom plate.

Place the 2 large wood blocks and make
sure there is no glass granulate under-
neath.