Faber FEG4916F, Инструкция по эксплуатации

Страница: 20 / 140

20
Receiver and Remote Batteries
Pairing Remote with Fireplace Receiver
Remote Control Batteries
• 2 × AAA (alkaline recommended) .
• Low battery indicator on handsets with display .
• Battery replacement is recommended every
2 years .
Receiver Batteries
• 4 × AA (alkaline ONLY)
• Low battery indicator: Frequent beeps for 3 seconds
when motor turns .
• If A/C adaptor is not used, battery replacement is
recommended at the beginning of each heating
season as part of the yearly service check .
Your remote will come paired with the fireplace
receiver and will be ready for operation out of the box .
In the event of remote or receiver replacement, use
the following procedure to pair the remote with the
receiver:
1 . Press and hold the receiver’s reset button (see
Figure 1) until you hear two (2) beeps . The first
beep is short, and the second beep is long . After
the second beep, release the reset button .
2 . Within the subsequent 20 seconds, press the
20 / 30
INSTALLATION AND OPERATING INSTRUCTIONS FOR OEM USE ONLY
© 2019 Mertik Maxitrol GmbH & Co. KG,
All Rights Reserved.
selected
1 2
ON
AM
PM
OFF
ON TIME SETTING (PROGRAM 1):
7. , , is displayed, is dis-
played shortly, and hour flashes.
8. To select hour press or button.
9. To confirm press button. , ,
is displayed, displayed shortly,
and
minutes
flash.
10. To select minutes press or but-
ton.
11. To confirm press button.
OFF TIME SETTING (PROGRAM 1) :
1 2
ON
AM
PM
OFF
12. , , is displayed, is dis-
played shortly, and hour flashes.
13. To select hour, press or button.
14. To confirm press button. , ,
is displayed, is displayed
shortly, and
minutes
flash.
15. To select minutes press or but-
ton.
16. To confirm press button.
NOTE: Either continue to PROGRAM 2 and set ON and OFF
times or stop programming at this point, and PRO-
GRAM 2 remains deactivated.
NOTE: PROGRAM 1 and 2 use the same ON (Thermostatic)
and OFF temperatures for , and Daily Timer ( ,
, , , , , ). Once a new ON (Thermostatic) and / or
OFF
temperature has been set, that temperature be-
comes the new default setting.
NOTE: If , or Daily Timer are programmed for PRO-
GRAM 1 and PROGRAM 2 ON and OFF times, these
become the new default times. The batteries must be
removed to clear the PROGRAM 1 and PROGRAM 2
ON and OFF times and temperatures.
or Daily Timer ( , , , , , , ) selected
▪ Set ON time and OFF time using same procedure as “ se-
lected ” (above).
▪ : Set
ON
time and
OFF
time for both Saturday and Sunday.
▪ Daily Timer: Unique
ON
and
OFF
times may be set for a single
day of the week, for multiple days of the week, or for every day
of the week.
▪ Wait to finish setting.
2
ND
BURNER FEATURE
The latching solenoid valve will open automatically after ignition
or after switching the system OFF , so that the maximum flow of
gas is supplied to both burners assisting with the ignition process.
After pressing the button for the 2
nd
Burner the motor will turn 7
seconds in the ON direction until the max. position is reached.
1 2
ON
AM
PM
OFF
ON
:
▪ To switch a burner ON , press the
button.
▪ displayed.
OFF :
▪ To switch the burner OFF , press the
button.
▪ disappears.
NOTE:
The latching solenoid valve cannot operate manually. If
the Receiver battery runs down it will remain in the last
operating position.
ECO MODE
AM
ON :
▪ Press button to enter Eco Mode.
▪ is displayed.
OFF :
1. Press button.
2. Press or button to enter Manual
Mode.
3. Press button to enter Thermostatic
Mode.
4. Press button to enter Program
Mode.
CIRCULATING FAN OPERATION
AM
Circulating fan has 4 speed levels from
low (1 bar) to high (4 bars).
ON / SETTING:
1. Press button and hold until
flashes.
2. Press button to increase fan speed
and button to decrease fan speed.
3. To confirm setting either press but-
ton or wait ( displayed).
OFF :
▪ Press button until all 4 speed level
bars disappear.
NOTE: SETTING only. If the fan was not switched OFF after
last use, it starts automatically 4 minutes after ignition
at maximum speed and goes to the last set level after
10 seconds. The fan stops 10 minutes after the gas is
OFF
or at pilot.
button on the handset until you hear two additional
short beeps confirming the code is set . If you hear
one long beep, this indicates the code learning
sequence has failed or the wiring is incorrect .
Figure 1
CAUTION: DO NOT USE a screwdriver or other metallic object to remove the batteries from
the battery box! This could cause a short circuit to the system .