background image

 

 

Installation Instructions 

VI-COWL 

Product Number: VC2900

 

2010 - 2018 DODGE 2500 

            

Copyright 2009 Fab Fours, Inc

. Page 3 of 19 

VC2900_Installation_Manual_REV_A

 

 

Overview 

 

Congratulations on your new purchase of the Fab Fours Vi-Cowl Accessory. 

 

Your Vi-Cowl was designed in 3-D from digitized data, CNC laser cut, fabricated, 
and powder coated… all in the U.S.A. Enjoy the fit and finish of a Vi-Cowl from Fab 
Fours, Inc. 
 

WARNING: 

This product was designed to be used with the 16-17 Dodge 2500 only. 

 
 

Contents 

Overview ............................................................................................................................. 3

 

I.

 

Tools Required ............................................................................................................ 4

 

II.

 

Provided Material: ................................................................................................... 4

 

III.

 

Factory Vehicle Prep................................................................................................ 6

 

IV.

 

Wiper cowl modification ....................................................................................... 10

 

V.

 

Fab Fours hood hinge installation .......................................................................... 10

 

VI.

 

Hood Installment .................................................................................................... 12

 

VII.

 

ViCowl Pre-Assembly ........................................................................................... 13

 

VIII.

 

ViCowl Installation ............................................................................................ 15

 

IX.

 

Maintenance/Care .................................................................................................. 19

 

X.

 

Contact Information ............................................................................................... 19

 

More than expected… Better than expected.

 ............................................................... 19

 

 

 

 
 
 

 

Содержание VI-COWL




















Отзывы: