background image

FIGURE 8. AIR FLOW INDICATION

FIGURE 9. FAULT DISPLAY 

ASP122-00

ASP120-00

lay from 0 to 60 seconds. 

AIR FLOW DISPLAY

The FAAST XS system uses ultrasonic airflow sensing and displays the status in 
real time on the user interface. The air flow display consists of 10 green LEDs at 
the bottom of the device to display current flow balance as shown in Figure 8. 

The green segments on the air flow pendulum indicate how close the current 
air flow is to a high or low fault threshold. The default threshold for a fault 
condition is + or – 20% from airflow baseline. This fault threshold is configu-
rable using the PipeIQ software. During normal operation two adjacent indica-
tors are green and correspond to the current air flow entering the detector for 
the inlet being displayed. When air flow is balanced, these two indicators will 
be centered in the pendulum. As air flow increases or decreases, the indicators 
will move to the left in the case of a low flow condition, or right in the case of 
a high flow condition. A flow fault occurs when the flow boundary threshold 
has been exceeded longer than the flow fault delay period. The fault relay will 
be set when this occurs.

Detailed air flow information can also be read by accessing the ‘Air Flow’ 

menu in the device’s LCD display.

FAULT DISPLAY

The FAAST XS user interface displays faults in two ways, through amber LEDs 
on the right side of the user interface, and also on the LCD screen. The four 
Fault LEDs are:

Fault

Isolate

Disable

Low Voltage

 

6 ASUG80001

If the General Fault LED is ON, the fault condition will be shown on the LCD 
display under the Active Faults menu. The possible fault conditions are:

TYPE

DESCRIPTION

ACTIVATED RELAY

Low Flow Fault

Device air flow below the 
boundary and delay programed 
by the user.

Fault

Configuration

Configuration of device with 
configuration software has 
failed.

Fault

Device was interrupted with a 
power loss during configura-
tion. A Reset will clear this 
fault and device will revert 
back to it’s last good configu-
ration.

Fault

Device is new and has not 
been configured.

Fault

Device has corrupt configura-
tion and is unable to operate.

Fault

Drift Blue Fault

Device blue signal has reached 
the long term drift limit.

Fault

IR Laser Drift Fault Device IR Laser signal has 

reached the long term drift 
limit.

Fault

Sensor Fault

Device sensor is not work-
ing and requires immediate 
replacement

Fault

External Monitor 
Fault

External monitor detects open. Fault

Time Fault

Internal Time needs updating. Fault

Aspirator Fault

Indicates the fan has stopped 
working and requires immedi-
ate attention.

Fault

Filter Fault

Device filter is clogged and 
requires replacement

Fault

Disable Fault

Device has been put in disable 
mode.

Isolate

Isolation Fault

Device has been put in isolate 
mode.

Isolate

High Flow Fault

Device air flow above the 
boundary and delay pro-
gramed by the user.

Fault

Low Voltage Fault

Device Input voltage is low 

Fault

Содержание XS 7100X













Отзывы: