![background image](http://html1.mh-extra.com/html/faac/750-standard/750-standard_manual_3102020019.webp)
19
F
+
+
Advanced Programming:
To access ADVANCED PROGRAMMING, press and hold key F
and then press key +:
• Release key +, the unit displays the name of the first
function.
• Release key F, modify the value of the function with keys
+ and -.
• Press and hold key F, the unit displays the name of the
next function, and if you release it, the value that can be
modified with keys + and -.
• When you reach the last function, press F to exit the pro-
gram, the unit resumes monitoring input status.
The following table shows the sequence of functions
accessible in ADVANCED PROGRAMMING:
ADVANCED PROGRAMMING
MAXIMUM TORQUE AT INITIAL THRUST:
The motors operate at maximum torque
(ignoring the torque setting) at start of
movement. Useful for heavy leaves.
= Active
= Disabled
LAST STROKE AT CLOSING:
The motors are activated at full speed for 1
second to facilitate locking of the electric lock.
= Active
=Disabled
REVERSING STROKE:
Before opening, while the gate is closed,
the motors thrust to close for 2 seconds thus
facilitating release of the electric lock.
= Active
= Disabled
LEAF 2 OPENING DELAY (2 s):
Enables delayed start (at opening) of leaf 2,
avoiding interference between leaves.
= Active
= Disabled
OPENING FAIL SAFE:
If this function is activated, it enables the
monitoring of the opening safety photocell
before the opening movement. If the test fails
the gate does not open.
= Active
= Disabled
PRE-FLASHING (5 s):
Activates the flashing lamp for 5 seconds before
start of movement.
= Active
= Disabled
ELECTRIC LOCK ON LEAF 2:
For using the electric lock on leaf 2 instead
of on leaf 1.
= Active
= Disabled
INDICATOR-LIGHT:
: the output functions as a standard indicator-
light (ON at opening and pause, flashing at
closing, and OFF when gate is closed).
: the output is ON when the gate is open or
in pause. OFF in all other conditions.
the output is ON when the gate is closed.
OFF in all other conditions.
All other values correspond to the extra time
compared to normal work time (opening or
closing) when the output can be used - via a
relay - to power a courtesy light. Time can be
adjusted from to
sec. in 1 sec. steps,
and from to
min. in 10 sec. steps.
CLOSING PHOTOCELLS REVERSE AT RELEASE:
Enable this function if you want the closing
photocells to stop movement and reverse at
release. Default setting is immediate reverse.
= Active
= Disabled
ASSISTANCE REQUEST (combined with next
function):
If activated, at the end of countdown (settable
with the next function i.e. “Cycle programming”)
it affects 8 s of pre-flashing at every Open
pulse (job request). Can be useful for setting
scheduled maintenance jobs.
= Active
= Disabled
CYCLE PROGRAMMING:
For setting countdown of system operation
cycles. Settable (in thousands) from to
thousand cycles. The displayed value is updated
as cycles proceed.
This function can be used to check use of the
board or to exploit the “Assistance request”.
OPENING No. 2 FAIL SAFE:
When enabled the STOP input can be used
for the connection of a second monitored
opening safety device
= Active
= Disabled
Exit from programming and return to inputs
status monitoring.
NOTE
: Parameter modifications take effect immediately.
Exit out of programming to save changes. If the equipment
is powered down before returning to normal status monitor-
ing, any unsaved modifications will be lost.
To restore programming defaults, press and hold the
three b, -, F simultaneously for 5 seconds.
EXTRA WORK TIME:
If reversing occurs, and if the leaf does not
reach its end contact point, you can activate
this function to increase work time.
= Active
= Disabled
Display
Function
Default
Display
Function
Default