![background image](http://html1.mh-extra.com/html/faac/746-e-r-z20/746-e-r-z20_translation-of-the-original-instructions_3123407005.webp)
746 E R
5
732099 - Rev.D
Tr
ansla
tion of the original instruc
tions
ENGLISH
1. INTRODUCTION TO THIS INSTRUCTION MANUAL
This manual provides the correct procedures and requirements for
installing 746 E R and maintaining it in a safe condition.
When drafting the manual, the results of the risk assessment con-
ducted by FAAC S.p.A. on the entire product life cycle have been taken
into account in order to implement effective risk reduction measures.
The following stages of the life cycle of the product have been con-
sidered:
-
Delivery/handling
-
Assembly and installation
-
Set-up and commissioning
-
Operation
-
Maintenance/troubleshooting
-
Disposal at the end of the product’s life cycle
Risks arising from installation and using the product have been taken
into consideration; these include:
-
Risks for the installation/maintenance technician (technical
personnel)
-
Risks for the user of the automation system
-
Risks to product integrity (damage)
In Europe, the automation of a gate falls under the Machinery Directive
2006/42/EC and the corresponding harmonised standards. Anyone
automating a gate (new or existing) is classified as the Manufacturer
of the Machine. They are therefore required by law, among other
things, to carry out a risk analysis of the machine (automatic gate in
its entirety) and take protective measures to fulfil the essential safety
requirements specified in Annex I of the Machinery Directive.
FAAC S.p.A. recommends that you always comply with the EN 12453
standard and in particular that you adopt the safety criteria and de-
vices indicated, without exception, including the dead-man function.
This manual also contains general information and guidelines, which
are purely illustrative and not exhaustive, in order to facilitate the ac-
tivities carried out by the Manufacturer of the Machine in all respects
with regard to carrying out the risk analysis and drafting the instruc-
tions for use and maintenance of the machine. It should be clearly
understood that FAAC S.p.A. accepts no liability for the reliability and/
or completeness of the above instructions. As such, the manufacturer
of the machine must carry out all the activities required by the Machi-
nery Directive and the corresponding harmonised standards on the
basis of the actual condition of the locations and structures where the
product 746 E R will be installed, prior to commissioning the machine.
These activities include the analysis of all the risks associated with
the machine and subsequent implementation of all safety measures
intended to fulfil the essential safety requirements.
This manual contains references to European standards. The au-
tomation of a gate must fully comply with any laws, standards and
regulations applicable in the country where installation will take place.
Unless otherwise specified, the measurements provided in the instructions
are in mm.
1
Symbols: notes and warnings on the instructions
F
WARNING ELECTRIC SHOCK HAZARD - The operation or step described must
be carried out following the instructions provided and according to the safety
regulations.
!
WARNING, personal injury hazard or risk of damage to components - The
operation or step described must be carried out following the instructions
provided and according to the safety regulations.
WARNING - Details and specifications which must be respected in order to
ensure that the system operates correctly.
RECYCLING AND DISPOSAL - The materials used in manufacturing, the batteries
and any electronic components must not be sent to landfill. They must be
taken to authorised recycling and disposal centres.
FIGURE E.g.
1
-3 see Figure 1 - item 3.
TABLE E.g.
1
see Table 1.
§
CHAPTER/SECTION
E.g. §1.1 see Section 1.1.
STATUS OF THE LEDS ON THE BOARD
LED off
LED on
LED flashing
3
Symbols: personal protective equipment
Personal protective equipment must be worn to protect against hazards (e.g. crushing,
cutting, shearing etc.):
Obligation to wear mask/goggles to protect the eyes from the risk of frag-
ments due to the use of drill or welder.
Obligation to wear work gloves.
Obligation to wear safety footwear.
2
Symbols: safety signs and symbols (EN ISO 7010)
GENERIC HAZARD
Personal injury hazard or risk of damage to components.
ELECTROCUTION HAZARD
Risk of electric shock from live parts.
CRUSHING HAZARD
Risk of crushing to the hands/feet due to the presence of
heavy parts.
CUTTING/AMPUTATION/PUNCTURE HAZARD
Cutting hazard due to the presence of sharp components or the
use of pointed/sharp tools (drill).
SHEARING/TRAPPING HAZARD
Risk of fingers and hands being sheared or trapped due to
moving parts.
BURNING OR SCALDING HAZARD
Risk of burns due to the presence of high-temperature parts.
1.1 MEANING OF THE SYMBOLS USED
Содержание 746 E R Z20
Страница 1: ...746 E R Z16 746 E R Z20 Translation of the original instructions...
Страница 41: ...746 E R 41 732099 Rev D...
Страница 42: ...746 E R 42 732099 Rev D...
Страница 43: ......