F.u.n.k.e. TRT800A-OLED Скачать руководство пользователя

Страница: 24 / 48

TRT800A / P/N 800ATC-A-(2xx)-(3xx)

Operation and Installation

Document-No: 03.2114.010.71e / Revision: 2.00

3.8

Antenna

3.8.1

Antenna Selection

•

Recommended antennas: see section 3.11 Accessories

•

Choose an antenna type compatible with the vehicle and the

mounting location.

•

Specified features depend on proper installation of the antenna.

•

The radiation pattern needs to be verified considering aircraft type

and mounting location.

•

The electrical interference between the antenna and any other

equipment must be taken into account in such a way that no
reduction of the performance of any other system will occur.

•

Install only certified antennas!

3.8.2

Installation Recommendation

•

Take note of the antenna manufacturer’s instructions.

•

The usually deployed Dipole- or Blade antennas necessarily

require a high frequency capable solid metal ground plane at the
antenna base.

•

For installation in composite aircrafts, ground planes are to be

added. The ground plane should be as large as possible but in any
case not smaller than 10 cm x 10 cm. If in doubt, please contact
the aircraft manufacturer.

•

Keep away three feet from any other antenna.

•

Pursue mounting in vertical position under the belly in flight

direction.

3.8.3

Antenna Wiring

•

Suitable antenna cables: see section 3.11 Accessories

•

Keep wiring as short as possible.

•

The smallest cable bend radius is 10cm. Avoid sharp bends.

•

Keep away from an ADF antenna cable at least 12 inches.

•

Electrical connections to the antenna shall be protected against

moisture to avoid loss of efficiency.

Содержание TRT800A-OLED

















































Результаты поиска

Содержание TRT800A-OLED

Отзывы:

Похожие инструкции для TRT800A-OLED

Бренды по названию

Популярные бренды

F.u.n.k.e. TRT800A-OLED, Эксплуатация и установка

Результаты поиска

Содержание TRT800A-OLED

Отзывы:

Похожие инструкции для TRT800A-OLED

Бренды по названию

Популярные бренды