F.F. Group 41346, Оригинальное руководство пользователя

Страница: 5 / 28

English | 5
www.ffgroup-tools.com
f f
Allow the tool to come to a complete stop before put-
ting it down. A running tool will jerk when the blade tip
contacts any surface.
f f
Always wear safety glasses or goggles, normal prescrip-
tion eye or sunglasses are not safety glasses
f f
Do not cut oversized work pieces
f f
Do not cut nails or screws unless you are using a blade
specifically designed for this purpose, inspect your ma -
terial before cutting
f f
Before switching on the tool, be sure the blade in not
contacting the work piece.
f f
Keep hands away from moving parts and on the top
surface of the work piece. Do not place hands below
work surface while saw is operating.
f f
Check your area for proper clearance before cutting.
This will avoid cutting into your workbench, the floor,
etc.
TECHNICAL SPECIFICATION
Article Number 41346
Mains voltage
V
Hz
230-240V
50HZ
Output power W 1.050
Stroke rate (no load) min 1 0-2.500
Stroke length mm 28
Max saw depth in wood mm 150
Weight (without acces-
sories) approx.
Kg 3,4
Sound emission values determined according to
EN 60745-1
Typically the A-weighted noise levels of the prod -
uct are:
Sound pressure level dB(A) 92,2
Sound power level dB(A) 103,2
Uncertainty K dB 3
Wear hearing protection!
Vibration total values a
h
(triax vector sum)
and uncertainty K determined according to EN
60745-1
Cutting chipboard:
a
h
m/s
2
24,62
K m/s 2 1,5
Cutting sheet metal:
a
h
m/s
2
21,25
K m/s
2
1,5
Cutting wooden beam:
a
h
m/s
2
25,65
K m/s
2
1,5
Function description
1. Blade
2. Pivot shoe
3. Quick-release blade clamp
4. Carbon brush cover
5. Indicator light
6. On/off switch trigger
7. Lock-on button
8. Cap screws
Assembly
Always check that the power supply corresponds to
the voltage on the rating name plate. To avoid acci -
dental start, check to make sure lock-on button is not
engaged prior to plugging in tool and you finger is not
touching the on/off switch trigger.
Install the blade
1. Unplug the power cord first.
2. Rotate the Quick-release blade clamp 3 anticlock-
wise with hand
3. At the same time push blade 1 to the deepest po-
sition, then release the quick-release blade clamp,
make sure it is securely fastened.
WARNING! Before plugging in power cord, always
pull on the blade to make sure it is securely locked in
the clamp. Failure to do so may result in serious injury.
OPERATION
Switch on/off
f f
Connect the plug to the power mains, the power
indicator light 5 is illumed until the tool disconnect
from the power mains.
f f
Turn on or turn off the tool by squeezing or releas -
ing the switch trigger 6 .
f f
For continuous operation just press the lock-on but -
ton 7 on the left side of the handle.
To change position of the pivot shoe assembly
f f
Unplug your saw. WARNING: Failure to unplug your
saw could result in accidental starting causing seri-
ous injury.
f f
Loosen the both cap screws in the gear frame with
hex. Key
f f
Reposition pivot shoe assembly in or out.
f f
Retighten both cap screws securely. Do not over
tighten cap screws.
f f
Remove Hex. Key.
WARNING: Cutting into electrical wiring in walls can
cause blade, blade clamp, and saw bar assembly to be-
come electrically live. Do not touch metal parts when
cutting into a wall; grasp only the insulated gripping
surfaces provided by the tool. Make sure hidden elec -
trical wiring, water pipes, and mechanical hazards are
not in the blade path when cutting into a wall.
General cutting
f f
Clamp your work piece if it is portable, rest the front
shoe of the saw on your work piece (be sure the blade
is not contacting the work piece) and start the saw, ex-
erting enough pressure in the direction of the cut to
keep the shoe pressed firmly against the work piece
at all times. Do not force the cut or stall the saw. Don’t
bend or twist the blade let the tool and the blade do