Extron electronics TPS150, Руководство пользователя

Страница: 42 / 52

Serial Communications, cont’d
TPS150 Switching and Transmission System • Serial Communications 4-16
Command/response table for programming and operating the TPT150 (Cont’d)
Command ASCII Command Response Additional description
(host to switcher) (switcher to host)
Program projector power and input command codes (continued)
Reset button code (ASCII or hex) [PCL1
X6
@] [R0•
X1
•PCL1
X6
@•] Clear any codes assigned to a
button. The transmitter does not
send any code when the button is
pressed.
Assign a projector power timeout [TOUT05
X9
] [R0•
X1
•TOUT05
X9
•] Set the transmitter to issue the
power off command
X9
minutes
after power on.
Example: [TOUT05060] [R0•97•TOUT05060•] The projector is powered off after
60 minutes.
View the projector power timeout [TOUT05?] [R0•
X1
•TOUT05?•
X9
] The projector power timeout is
set to
X9
minutes.
Projector commands
Send projector power code [PPWR
X3
] [R0•
X1
•PPWR
X3
•] Send the projector power on or
off (
X3
) command. (0 = power
off, 1 = power on).
Toggle the projector power [PPWR] [R0•
X1
•PPWR•] If the projector power is on, turn
it off; if it is off, turn it on.
Set the power on delay [PPWRD1
X10
] [R0•
X1
•PPWRD1
X10
•] Set the power on (warm up)
delay to
X10
seconds. During the
delay, serial commands to the
projector and TPT150 front panel
operation are disabled.
Set the power off delay [PPWRD0
X11
] [R0•
X1
•PPWRD0
X11
•] Set the power off (cool down)
delay to
X11
seconds. During the
delay, serial commands to the
projector and TPT150 front panel
operation are disabled.
Enable automatic audio mute and [PPWRM1] [R0•
X1
•PPWRM1•] Mute the audio when the
unmute during the projector power projector power off command is
command. issued; unmute the audio when
the power on command is issued.
Disable automatic mute/unmute [PPWRM0] [R0•
X1
•PPWRM0•]
Serial port configuration
Set both serial ports’ parameters [CP1
X12 X13 X14 X15
02
X12 X13 X14 X15
0]
[R0•
X1
•CP1
X12 X13 X14 X15
02
X12 X13 X14 X15
0•]
Command description: [CP1 0] 02 X12 X13 X14 X15
Baud
rate
1 = transmitter port
Parity Stop
bits
Flow
control
X12 X13 X14 X15
Baud
rate
Parity Stop
bits
Flow
control
2 = receiver port
Example: [CP130000241110] [R0•97•CP130000241110•] Set the transmitter’s serial port to
9600 baud, no parity, and 1 stop
bit, Xoff; set the receiver’s serial
port to 19200 baud, odd parity, 2
stop bits, and Xon.
If you change the transmitter’s settings, you may not be able to read the response until you change the controller’s
settings.
Set transmitter’s serial port parameters [CP1
X12 X13 X14 X15
0] [R0•
X1
•CP1
X12 X13 X14 X15
0•]
Reset both serial ports to default [CP1@] [R0•
X1
•CP1@•] Reset both serial ports to their
default settings: 9600 baud, no
parity, 1 stop bit , and Xoff.
View both serial ports’ parameters [CP1?] [R0•
X1
•CP1?•
X12 X13 X14 X15 X12 X13 X14 X15
]