Extron electronics SW2 DVI A Plus страница 37 Скачать руководство пользователя | Manualshive

Страница: 37 / 45

background image

SW DVI Plus Series • Reference Information

31

31

31

Reference

Information

•

Specifications

•

Part Numbers

•

Mounting the SW DVI Plus Switcher

Specifications

NOTE:

*Appropriate DVI-D to HDMI cables or adapters are required for HDMI signal input/output.

NOTE:

The SW DVI Plus Series are not HDCP compliant.

Video

Maximum data rate ........................   4.95 Gbps (1.65 Gbps per color)
Maximum pixel clock ......................   165 MHz
Resolution range ............................   Up to 1920x1200 or 1080p @ 60 Hz
Formats ..........................................   RGB and YCbCr digital video
Standards .......................................   DVI 1.0, HDMI

Video input

Number/signal type ........................   2, 4, 6, or 8 single link DVI-D (or HDMI*)
Connectors ....................................   2, 4, 6, or 8 female DVI-I
Equalization ...................................   +6 dB or +12 dB, switch selectable for each input

Video output

Number/signal type ........................ 1 single link DVI-D (or HDMI*)
Connectors .................................... 1 female DVI-I

Audio

Gain ...............................................   Unbalanced output: 0 dB; balanced output: +6 dB
Frequency response ........................   20 Hz to 20 kHz, ±0.05 dB
THD + Noise ...................................   0.01% @ 1 kHz at nominal level
S/N .................................................   >90 dB at maximum output (unweighted)
Crosstalk ........................................   <-45 dB @ 20 kHz, -72 dB @ 1 kHz or below
Stereo channel separation ..............   >80 dB @ 20 Hz to 20 kHz

Audio input

Number/signal type ........................   2, 4, 6, or 8 stereo, unbalanced
Connectors ....................................   (2, 4, 6, or 8) 3.5 mm mini audio jacks (tip = L, ring = R, sleeve = GND)
Impedance .....................................   >10k ohms unbalanced, DC coupled
Nominal level .................................   -10 dBV (316 mVrms)
Maximum level ...............................   +8.2 dBV, unbalanced at 1% THD+N

NOTE:

0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV

≈

2 dBu

«
...
35
36
37
38
39
...
»

Содержание SW2 DVI A Plus














































Отзывы:

Нет отзывов

Похожие инструкции для SW2 DVI A Plus

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 281

Бренд: Camozzi Страницы: 2

Бренд: D-Link Страницы: 7

SkyEdge II-c Capricorn Pro 4 AC Series

Бренд: Gilat Страницы: 2

Бренд: N-Tron Страницы: 132

Бренд: Imtex-Controls Страницы: 2

DigiTOOLS VS-41USB

Бренд: Kramer Страницы: 8

TK-205K - PS/2 KVM Switch

Бренд: TRENDnet Страницы: 11

FL SWITCH SFN 16TX

Бренд: Phoenix Contact Страницы: 6

852-1411/000-001

Бренд: WAGO Страницы: 40

Бренд: Delta Electronics Страницы: 31

Бренд: Eaton Страницы: 2

Бренд: LevelOne Страницы: 76

Бренд: N-Tron Страницы: 15

Бренд: Ubiquiti Страницы: 23

Бренд: Exsys Страницы: 2

SM24-1000SFP-AH

Бренд: Transition Networks Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды