Extron electronics Matrix 3200 Series Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 70

background image

Upgrades and Troubleshooting, cont’d

Matrix 3200/6400 Series

•

Upgrades and Troubleshooting

5-6

Troubleshooting a Matrix 3200/6400 System Problem

All Matrix 3200/6400 BME front panels include LEDs at the bottom of the panel
which are bracketed and labeled DIAGNOSTICS. These LEDs (Figure 5-6.A)
indicate the current status of the BME power supplies, the RS232/BME/MKP

1

Communications RX and TX lines, and the System Status. The following
descriptions include normal/failure/status conditions for each LED.

Power Supplies

PV

Green LED

ON = Normal
OFF = Failure

Primary -V

Green LED

ON = Normal
OFF = Failure

RedV

Green LED

ON = Normal
OFF = Failure (or Redundant not present)
Blinking = RedV supplying full +V load
(indicates PV power supply failure)

Redundant -V

Green LED

ON = Normal
OFF = Failure (or Redundant not present)
Blinking = Redundant -V supplying full +V
load (indicates Primary -V power supply failure)

If a BME fails to power ON, check the BME external AC fuse (see Page 5-7).
If the Diagnostic LEDs indicate that a power supply has failed, check the power
supply fuse (see Page 5-7).

BME #0 must be powered ON at the same time or after other BMEs. Any BME
powered on after BME #0 will not be seen by the internal system software.

Communications

RS232 TX - Red LED ON/Blinking = BME is transmitting data to Host
RS232 RX - Green LED ON/Blinking = BME is receiving data from Host
BME TX - Red LED ON/Blinking = BME is transmitting data
BME RX - Green LED ON/Blinking = BME is receiving data
MKP TX - Red LED ON/Blinking = BME is transmitting to Remote keypad

MKP RX - Green LED ON/Blinking = BME is receiving from Remote keypad

1. MKP TX/RX LEDs are not present on SYNC BMEs.
2. MKP LED conditions above apply only to BME #0.
3. RS-232 LED conditions above apply only to BME #0.
4. A communications failure between BME #0 and other BMEs could be
caused by one BME loading down the BME TX or RX line. To determine if
that is the case, run the RJ-11 BME COMM interconnecting cable to bypass
each BME one at a time.

System Status

Amber LED

ON = Normal
OFF = System failure - Call Extron Tech Support
Blinking = Busy

Checking/Replacing the BME External AC Input Fuse

The AC power input cord plugs into the Power-Switch/Fuse assembly which is
located on the rear panel in the lower left corner of the BME. To check/replace the
external fuse, remove the power-cord and insert the tip of a small screwdriver blade

«
...
46
47
48
49
50
...
»

Содержание Matrix 3200 Series







































































Отзывы:

Нет отзывов

Похожие инструкции для Matrix 3200 Series

xStack DGS-3427

Бренд: D-Link Страницы: 246

Бренд: National Instruments Страницы: 23

Бренд: hager Страницы: 6

Бренд: Articona Страницы: 2

Бренд: LevelOne Страницы: 76

Summit X450-G2-24t-GE4

Бренд: Extreme Networks Страницы: 2

Бренд: Exsys Страницы: 14

Бренд: Qlogic Страницы: 412

Бренд: A-Neuvideo Страницы: 20

Бренд: N-Tron Страницы: 169

Бренд: EnGenius Страницы: 72

ICS5400PTP-12GT12GS4XS

Бренд: 3onedata Страницы: 3

Бренд: NETGEAR Страницы: 2

Thinklogical TLX640

Бренд: Belden Страницы: 48

FLOJET 02095502

Бренд: Xylem Страницы: 28

Бренд: Rose electronics Страницы: 57

Бренд: Johansson Страницы: 16

Бренд: SMC Networks Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды