8
IPL EXP I/O Series • Setup Guide (Continued)
Control, Bidirectional — LAN/PoE (Ethernet)
R
IPL EXP RIO8
100
LINK
ACT
IPL EXP RIO8
LAN/PoE
IPL EXP 200
LAN / PoE+
RJ-45
Connector
Insert
Twisted Pair Wires
Pins:
1
2
3
4
5
6
7
8
Rear
Panel
Front Panel,
IPL EXP RIO8
Front Panel,
IPL EXP RIO8
• Connect to a network that
provides PoE+
(IPL EXP RIO8) or PoE or
PoE+ (all other models) or to
an active power injector.
• Front panel LED ( ) blinks
during boot-up and remains
lit when the unit is powered
and operational.
Ethernet
Link
LED
Activity
LED
100 Mbps
Connection
Network is
active.
Data is being
sent/received.
or
TCP/IP
Network
LAN (Ethernet)
Default protocol, public ports:
Default login
credentials:
• Username:
admin
or
user
• Password:
extron
• IPL EXP IP address: 192.168.
254.250
• Gateway IP address: 0.0.0.0
• Subnet mask: 255.255.255.0
• DNS address: 127.0.0.1
• DHCP client: off
• Link speed and duplex level: autodetected
• Data rates: 10/100Base-T
PC
PoE or PoE+
ATTENTION:
•
Power over Ethernet (PoE) is intended for indoor use only. It is to be connected only to networks or circuits that are not
routed to the outside plant or building.
•
L’alimentation via Ethernet (PoE) est destinée à une utilisation en intérieur uniquement. Elle doit être connectée
seulement à des réseaux ou des circuits qui ne sont pas routés au réseau ou au bâtiment extérieur.
MAC address:
Each IPL EXP expansion interface is assigned a unique user hardware ID number
(MAC address) (for example, 00-05-A6-05-1C-A0). You may need this address during configuration.
A label that indicates the MAC address is located on the rear of the unit.
Control, Unidirectional — IR/Serial
IR/SERIAL
S G S G
S G S G
S G S G
S G S G
1
2
5
6
3
4
7
8
Tx Rx G
RELAYS
1 2 C
COM 2
Tx Rx G
COM 1
IR/S
S G
Tx Rx G
COM
2
2
2
Tx Rx G
COM
M
1
1
R
R
R
R
RE
E
E
L
LA
YS
1 2 C
IPL EXP 200
RearPanel
To the IR Receiver of a
Projector, Display, or
Source Device
S
G
(-)
(+)
(-)
(+)
(+)
(-)
Two Single IR Emitters
Ground
IR Output Signal
Unidirectional
IR
IR or RS-232
Output
Ground
To a Projector,
Panel Display, or the
Wired IR Remote or
RS-232 Port of a
Source Device
IR/Serial Ports
Output options:
• IR (30 kHz to 300 kHz,
with or without carrier signals)
• Unidirectional RS-232
or
MAC: 00-05-A6-
XX-XX-XX
S/N: ####### E######
00-05-A6-XX-XX-XX
MAC: 00-05-A6-
XX-XX-XX
S/N: ####### E######
MAC
Address
NOTE:
The factory configured password
for this device has been set to the device
serial number. Passwords are case sensitive.
Performing a Reset to Factory Defaults reset
(see
extron
.
