Extron electronics FOXBOX 4G Rx VGA, Руководство пользователя

Страница: 22 / 35

FOXBOX 4G Tx/Rx • Remote Contr
ol
Remote Contr
ol, cont’d
3-6
FOXBOX 4G Tx/Rx • Remote Contr
ol
3-7
Command ASCII Command
(host to unit)
Response
(unit to host)
Additional description
Video mute
Mute output 1B
Blk1
]
Blank the video output.
Unmute output 0B
Blk0
]
Output video.
Show video mute status B
X!]
Video output mute status is
X!
(0 = unmuted, 1 = muted).
Display Data Channel (DDC) resolution and rate (FOXBOX 4G DVI only)
Set DDC resolution
41*
X@
*
X#
# DDC
X@
*
X#]
Select a DDC resolution.
Show DDC resolution 41#
X@
*
X#]
Show the DDC resolution.
Mode switch position
N
Only DIP switch 1 (the first
X$
) has any effect on the system operation. When the switch is on (up), the receiver is in daisy chain mode.
Show DIP switch position 8#
X$X$]
Show the rear panel DIP switch position.
Output sync format
Set output sync format
6*
X%
# Syn
Y%]
Set the sync format. 0 = RGBHV, 1 = RGsB.
Show output sync format 6#
X%]
Output sync polarity
Set output polarity negative 7*1#
Pol1
]
Set the receiver output polarity to always be negative.
Set polarity to the input 7*0#
Pol0
]
Polarity follows the video sync input to the transmitter.
Show output sync format 7#
X^]
Command/response table for SIS commands
Command ASCII Command
(host to unit)
Response
(unit to host)
Additional description
Horizontal shift
Set a horizontal position
X&
H Hph
X&]
Set horizontal centering to
X&
.
Increment position. +H
Hph
X&]
Shift the image one pixel to the right.
Decrement position -H
Hph
X&]
Shift the image one pixel to the left.
Show position H
X&]
Vertical shift
Set a vertical position
X&
/ Vph
X&]
Set vertical centering to
X&
.
Increment position +/
Vph
X&]
Shift the image down one line.
Decrement position -/
Vph
X&]
Shift the image up one line.
Show position /
X&]
Horizontal start
N When the controlling PC is connected to the receiver, the FOXBOX 4G can perform this command only if the
r
eceiver Tx to transmitter Rx
fiber cable is connected. The unit returns the E14 error if the RX fiber is not connected.
Set a start position
X*
) Hst
X&]
Set the horizontal location of the first active pixel in the
active window.
Example: 128)
Hst128
]
Set pixel 128 as the first active pixel.
Increment start position +)
Hst
X&]
Increase the horizontal start location value.
Decrement start position -)
Hst
X&]
Decrease the horizontal start location value.
Show start position )
X*]
Command/response table for SIS commands (continued)
N
X!
= Mute status 0 or 1 (0=umuted and 1=muted)
X@
= Resolution 1 through 15. See page 3-3
X#
= Refresh rate 1 = 50 Hz 2 = 60 Hz
X$
= Mode switch position 0 = off (down) 1 = on (up)
X%
= Output sync format 0 = RGBHV 1 = RGsB
X^
= Output sync polarity 0 = follow input 1 = force sync to negative
N
X&
= Horizontal and vertical position 0 to 255
X*
= Horizontal start 0 to 255