background image

 

DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation

17

 

Operation

The DTP T EU and DTP T MK units can be controlled only by SIS commands (see 

Simple 

Instruction Set Control

 on page 19) or the Product Configuration Software (see 

Product 

Configuration Software

 on page 26). This section contains basic information about 

operation details. Topics in this section include:

Indications 

PWR HDCP HDMI VGA AUTO

• 

Power LED

 — Lights when power is applied.

• 

HDCP LED

 — Lights when the HDMI input signal is encrypted.

• 

HDMI LED

 — Lights when an HDMI input signal is detected.

• 

VGA LED

 — Lights when a VGA input signal is detected.

• 

Auto LED

 — Lights when the device is in auto switch mode.

Switch Modes

The switching transmitter has three switch modes:

• 

Manual

 — The input must be selected manually using an SIS command

• 

Auto switch (VGA)

 — The switcher automatically selects the input with an active signal 

present and, if both are present, prioritizes the VGA input. 

This is the factory default 

mode

.

• 

Auto switch (HDMI)

 — The switcher automatically selects the input with an active 

signal present and, if both are present, prioritizes the HDMI input.

These modes can be selected through SIS commands (see 

Switch mode

 SIS commands 

on page 22) or the Product Configuration Software (see the PCS Help file)

.

EDID

To manage EDID on the DTP T EU and DTP T MK units, use SIS commands (see 

EDID

 SIS 

commands on page 23) or the Product Configuration Software (see the PCS Help file). The 
DTP T EU and DTP T MK units can record and save EDID in a user memory location, select 
a pre-defined EDID, or use EDID from a display connected to a receiver. EDID stored in the 
user memory location can come from the display connected to a receiver or a custom EDID 
imported through the Product Software.

Reset

Use the recessed Reset button on the side of the transmitter (see 

figure 3

 on page 7 and 

item 

G

 on page 8) to initiate a reset to the default settings. Press and 

hold

 the reset button 

for approximately 6 seconds. All front panel LEDs cycle. Release the button. This reset is the 
equivalent of issuing the 

Reset

 SIS command (

E

ZXXX

}

, see page 25).

Содержание DTP T EU 232









































Отзывы: