Extron electronics CCD 220 Скачать руководство пользователя страница 8

Страница: 8 / 12

Cable Cubby Drawer CCD 220 and CCD 320

•

Installation Guide (Continued)

Preparing the Cable Cubby Drawer

Step 1 — Disassemble the AAP frame from the Cable Cubby Drawer

Remove the bottom screws from

underneath the drawer (3 screws for
the CCD 220 and 5 for the CCD 320).

Remove each screw from the

side of the drawer and lift the AAP
frame up and out.

AAP Frame

Step 2 — Attach the AAP modules to the AAP frame

AAP frames allow you to populate the Cable Cubby Drawer with a combination of AAP modules. Follow the steps
below to assemble the connectivity modules of your choice.

HDM

VGA

AUD

USB

Position the AAP modules through

the front of the AAP frame.

Secure the AAP modules

with the #4-40 nuts included
with the AAP kits

Step 3 — Install Populated AAP frame onto the Cable Cubby Drawer

HDMI

VGA

AUDIO

USB

USB CHARGER

Reposition and secure the AAP frame

back onto the Cable Cubby Drawer
using the screws removed in Step 1.

Содержание CCD 220













Результаты поиска

Содержание CCD 220

Отзывы:

Бренды по названию

Популярные бренды

Extron electronics CCD 220, Руководство по установке

Результаты поиска

Содержание CCD 220

Отзывы:

Бренды по названию

Популярные бренды