Extron electronics Cable Cubby 1252 MS Скачать руководство пользователя страница 12

Страница: 12 / 12

Cable Cubby 1252 MS • Installation Guide (Continued)

68-3289-01 Rev. B

12 19

www.extron.com

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters:

Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide

on the Extron website.

Installation Checklist

Planning (page 1)

Check with local and state regulations before starting the installation

Check all parts and equipment before installation

Preparing the Table

Determine the best location for the enclosure

Determine cutout hole size based on lid thickness (page 3)

Cut the hole in the table and pre-drill mounting locations (page 3)

Fabricate Cable Cubby lid (page 3)

Preparing the Cable Cubby

Assemble Connectivity Modules (page 4)

Install the Modules (page 5)

Mount the Lid onto the Cable Cubby (page 6)

Mounting the Cable Cubby in the Table

Mount the Cable Cubby flush with the table (page 6)

If necessary, adjust the Cable Cubby height (page 7).

If necessary, install the trim brackets (page 8)

Installing optional equipment

Installing Retractors (page 8)

Installing a ZipClip mounting clip (page 9)

Installing a PMK 155 Product Mounting Kit (page 9)

Routing and Connecting Cables (page 10)

Содержание Cable Cubby 1252 MS













Результаты поиска

Содержание Cable Cubby 1252 MS

Отзывы:

Похожие инструкции для Cable Cubby 1252 MS

Бренды по названию

Популярные бренды

Extron electronics Cable Cubby 1252 MS, Руководство по установке

Результаты поиска

Содержание Cable Cubby 1252 MS

Отзывы:

Похожие инструкции для Cable Cubby 1252 MS

Бренды по названию

Популярные бренды