EXTREME SWITCHING 4450GTX-HTPWR+ Скачать руководство пользователя страница 4

Страница: 4 / 11

Installing the Virtual Services Platform 4000

on a table or shelf

You can install a single VSP 4000 switch on any flat surface. The surface must support the
combined weight of the switch and attached cables (from 15 and 20 pounds [7 to 9 kilograms]).

Note:

A factory-supplied 4450GTX-HT-PWR+ switch has a USB slot but no USB device or cover.

To install a VSP 4000 on a table or shelf, perform this procedure.

1. Attach the included rubber footpads on the bottom of the switch at the locations indicated.

2. Set the switch on a table or shelf as illustrated below. Allow at least 2 inches (5.1

centimeters) on each side for proper ventilation and at least 5 inches (12.7 centimeters) at
the back for power cord clearance.

November 2017

Installation Job Aid for VSP 4450GTX-HT-PWR+

Содержание 4450GTX-HTPWR+












Результаты поиска

Содержание 4450GTX-HTPWR+

Отзывы:

Похожие инструкции для 4450GTX-HTPWR+

Бренды по названию

Популярные бренды

EXTREME SWITCHING 4450GTX-HTPWR+, Инструкция по установке

Результаты поиска

Содержание 4450GTX-HTPWR+

Отзывы:

Похожие инструкции для 4450GTX-HTPWR+

Бренды по названию

Популярные бренды