EXTREME SWITCHING 4450GTX-HTPWR+ Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 11

background image

3. Insert and tighten the rack-mount screws.

Installing SFP transceivers

Install SFP transceivers by performing this procedure.

1. Remove the transceiver from the protective packaging.

2. Verify that the transceiver is the correct model for the network configuration.

3. Grasp the transceiver between your thumb and forefinger.

4. Insert the transceiver into the proper module on the switch. Apply a light pressure to the

transceiver until it clicks and locks into position in the module.

5. Remove the dust cover from the transceiver optical bores.

Removing SFP transceivers

Remove SFP transceivers by performing this procedure.

1. Disconnect the network fiber cable from the transceiver.

2. Use the locking mechanism on the transceiver to release it. The locking mechanism varies

from model to model as illustrated below.

November 2017

Installation Job Aid for VSP 4450GTX-HT-PWR+

6

«
...
4
5
6
7
8
...
»

Содержание 4450GTX-HTPWR+












Отзывы:

Нет отзывов

Похожие инструкции для 4450GTX-HTPWR+

Бренд: F5 Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды