Extreme Networks ExtremeWireless AP560i Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 46

Extreme Networks ExtremeWireless AP560i Скачать руководство пользователя страница 45

FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

•

This device may not cause harmful interference .

•

This device must accept any interference received, including interference that may cause undesired
operation.

This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.

FCC Radiation Exposure Statement

Warning
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance 20
cm between the radiator and your body.

European Waste Electrical and Electronic Equipment (WEEE) Notice

In accordance with Directive 2012/19/EU of the European Parliament on waste electrical and electronic
equipment (WEEE):

1. The symbol above indicates that separate collection of electrical and electronic equipment is

required.

2. When this product has reached the end of its serviceable life, it cannot be disposed of as unsorted

municipal waste. It must be collected and treated separately.

3. It has been determined by the European Parliament that there are potential negative effects on the

environment and human health as a result of the presence of hazardous substances in electrical and
electronic equipment.

4. It is the user's responsibility to utilize the available collection system to ensure WEEE is properly

treated.

For information about the available collection system, please contact Extreme Environmental
Compliance at [email protected].

Regulatory and Compliance Information

FCC Caution:

ExtremeWireless™ AP560i Access Point

45

«
...
43
44
45
46
»

Содержание ExtremeWireless AP560i















































Отзывы:

Нет отзывов