Extreme Networks Altitude 4522 Series Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 68

Extreme Networks Altitude 4522 Series Скачать руководство пользователя страница 57

Chapter 5: Regulatory Information

Altitude™ 4522 Series Access Point Installation Guide

57

Wireless Devices - Countries

Country Selection

Select only the country in which you are using the device. Any other selection will make the
operation of this device illegal.

NOTE

The US only models (4522i-US and 4522e-US) have the country code permanently set to the

US. The ROW models (4522i-ROW and

4522e-ROW) and EU models (4522i-EU and

4522e-EU)

cannot be configured for use in the US.

Operation in the US and Canada

The use on UNII (Unlicensed National Information Infrastructure) Band 1 5150-5250 MHz is
restricted to indoor use only, any other use will make the operation of this device illegal.

The available channels for 802.11 bg operation in the US are Channels 1 to 11. The range of
channels is limited by firmware.

Radio Frequency Interference Requirements—
FCC

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:

●

Reorient or relocate the receiving antenna

●

Increase the separation between the equipment and receiver

«
...
55
56
57
58
59
...
»

Содержание Altitude 4522 Series





































































Отзывы:

Нет отзывов