Extreme Flight LASER EXP ARF Скачать руководство пользователя | Manualshive

Страница: 33 / 41

background image

47. Attach a 24" extension to each servo lead and install both elevator servos.
Using the manufacturer supplied mounting hardware; mount both servos with the
output shaft toward the rear of the fuselage as shown in the picture below.

48. Thread a ball link on each end of the steel pushrod and secure to the servo arm
and elevator control horns with 2 x 3mm bolts, washers, and nylon insert locknut
as shown in the picture below. Be sure to use a drop of blue Loctite on all bolts!!!
Repeat the process for the other elevator.

33

«
...
31
32
33
34
35
...
»

Содержание LASER EXP ARF










































Отзывы:

Нет отзывов

Похожие инструкции для LASER EXP ARF

M-2A2 Bradley IFV

Бренд: Eduard Страницы: 6

Бренд: Black Horse Model Страницы: 20

Бренд: Fisher-Price Страницы: 2

Бренд: Stevens AeroModel Страницы: 29

Бренд: Tamiya Страницы: 24

Бренд: LEGO Страницы: 84

Бренд: Dancing Wings Hobby Страницы: 2

Бренд: Miniature Aircraft USA Страницы: 33

Junior Fly Ball

Бренд: Amewi Страницы: 8

Бренд: Multiplex Страницы: 32

Бренд: Faller Страницы: 8

Super Cub 25e ARF

Бренд: E-FLITE Страницы: 48

Бренд: Bill Hempel Страницы: 31

Бренд: marklin Страницы: 36

Бренд: Trix Страницы: 28

Бренд: marklin Страницы: 56

Бренд: REVELL Страницы: 60

Бренд: Seagull Models Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды