Extreme Flight LASER EXP ARF Скачать руководство пользователя | Manualshive

Страница: 17 / 41

background image

18. Locate the aileron servo mount and remove the covering from this area. Use a
sealing iron to seal the edges of the covering to the sides of the servo opening. Take
a few minutes to apply some CA to the joints of the servo rails and the ribs.

19. Attach a 6” servo extension to your servo and secure with thread or heat
shrink tubing. Attach the recommended 1.50” SWB Servo arm and electronically
center the servo arm. Use the manufacturer supplied mounting hardware to install
the servo with the output shaft toward the trailing edge of the wing.

17

«
...
15
16
17
18
19
...
»

Содержание LASER EXP ARF










































Отзывы:

Нет отзывов

Похожие инструкции для LASER EXP ARF

Бренд: Fei Bao Страницы: 64

Бренд: THUNDER TIGER Страницы: 28

Бренд: GRAUPNER Страницы: 47

Бренд: BUSCH Страницы: 8

Бренд: Multiplex Страницы: 17

Бренд: Eduard Страницы: 5

Бренд: Eduard Страницы: 4

PENNSYLVANIA K4 STREAMLINER

Бренд: Lionel Страницы: 2

Touch & Explore Activity Table 5408

Бренд: VTech Страницы: 13

Бренд: Zeller Страницы: 14

Бренд: Velleman Страницы: 8

U.S. GENERAL Junior 56515

Бренд: Harbor Freight Tools Страницы: 8

Hellcat Little Nugget

Бренд: H-KING Страницы: 18

No. 9 pay as you enter

Бренд: M.T.H. Страницы: 23

Бренд: Faller Страницы: 4

Бренд: Eduard Страницы: 3

Бренд: Eduard Страницы: 4

SH-3 Sea King interior

Бренд: Eduard Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды