Extreme Flight LASER EXP ARF Скачать руководство пользователя | Manualshive

Страница: 10 / 41

background image

9. Reinsert the assembly into the elevator and wipe away any excess epoxy with a
cloth and denatured alcohol. Place a 3mm bolt through the horns to help insure
proper alignment and set aside to dry. Repeat for the other elevator half.

10. Next remove the pin hinges from the horizontal stabs. Take note that one pin is
shorter than the others - this is to allow for clearance of the stab tube.

Note: There are several methods and adhesives that can be used for installing the
hinges. We will describe the way we do it as this method has proven itself over many
years of model building.

10

«
...
8
9
10
11
12
...
»

Содержание LASER EXP ARF










































Отзывы:

Нет отзывов

Похожие инструкции для LASER EXP ARF

Бренд: Fisher-Price Страницы: 6

Бренд: Air Hogs Страницы: 6

Spitfire placards

Бренд: Eduard Страницы: 3

Бренд: E-FLITE Страницы: 19

VOICE TECH RESCUE HEROES Wendy Waters Firefighter

Бренд: Fisher-Price Страницы: 2

HO Scale Under The Ties 309

Бренд: Kadee Страницы: 2

Education RENEWABLE ENERGY WATER POWERED...

Бренд: K'Nex Страницы: 20

PENNSYLVANIA K4 STREAMLINER

Бренд: Lionel Страницы: 2

Бренд: PLAYTIVE JUNIOR Страницы: 20

Бренд: Fisher-Price Страницы: 2

Бренд: Basic Fun Страницы: 2

Бренд: Tamiya Страницы: 24

Бренд: VBC Racing Страницы: 30

Switch & Go Dinos Seeker the T-Rex

Бренд: VTech Страницы: 11

Бренд: Fisher-Price Страницы: 2

COLLECT & BUILD RACECAR RALLY Series

Бренд: K'Nex Страницы: 20

Gravitrax LOOPING

Бренд: Ravensburger Страницы: 4

Origami 3D Ladybug 2568

Бренд: Alexander Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды