Extreme Flight ARF RC Скачать руководство пользователя | Manualshive

Страница: 9 / 16

background image

5.

Rudder installation. The 106" Edge includes hinges and hinge rod to make the rudder removable. Be sure

to take your time installing the hinges. Dry fit everything first!

Be sure to orient the hinges consistently on

each side/surface. Dry fit the hinges and install the hinge rod. Adjust hinge slots as necessary. Once

satisfied with hinge fit and placement, apply glue to hinge slots. Using a zip tie end to guide the glue in the

slots. Apply more glue to the hinge and insert. Do this for both the rudder and the vertical stabilizer. Clean

up the excessive glue before install hinge rod. Mate the rudder to the vertical stabilizer with the hinge rod

and adjust as necessary. Once satisfied, tape the rudder in place to dry. Checking frequently to clean up

excess glue. Move the hinge rod and clean excess glue to allow the hinges to move freely.

The hinge rod is

held in place by a wheel collar installed at the bottom

of the rod

.

«
...
7
8
9
10
11
...
»

Содержание ARF RC

















Отзывы:

Нет отзывов

Похожие инструкции для ARF RC

Ultimate EP 3D Profile

Бренд: E-FLITE Страницы: 40

Бренд: FB Jets Страницы: 39

BLACK FOREST FARM WITH BAKING COTTAGE

Бренд: Faller Страницы: 12

Бренд: Global Hobby Страницы: 32

Build-a-ma-Jigs Racetruck BX1221

Бренд: B Страницы: 2

Бренд: HOBBY ENGINE Страницы: 8

Бренд: Faller Страницы: 8

Бренд: LEGO Страницы: 68

Zoom Avia B.534 IV. Series Weekend

Бренд: Eduard Страницы: 2

Mercedes-Benz SLK

Бренд: Rastar Baby Страницы: 14

Бренд: Trix Страницы: 12

E-flite Eratix 3D Flat Foamy 860mm

Бренд: Horizon Hobby Страницы: 16

Бренд: Zhejiang Jiajia Ride-On Co. Страницы: 27

Бренд: Eduard Страницы: 4

Бренд: Radio Shack Страницы: 9

Бренд: LEGO Страницы: 84

CVN-65 Enterprise Part4

Бренд: Eduard Страницы: 8

He 111 H-6 bomb bay

Бренд: Eduard Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды