Extreme Flight ARF RC Скачать руководство пользователя страница 12

Страница: 12 / 16

6. Next we will install the main landing gear, axles, tires, wheel pants and wheel cuffs. Use the

provided bolts, washers and nuts from the main landing gear hardware kit to mount the

carbon gear to the fuselage.

Install the landing gear plate cover over the mounting nuts. Glue in place with Goop style silicon

glue.

Slide the landing gear cuffs into place against the fuselage and secure with Goop style silicon

glue.

Tape in place until glue is fully cured.

Insert the axles into the holes on the landing gear leg and secure with a washer and lock nut.

Grind a flat spot on the axles to fasten the set screw against providing a better grip. Now install

one wheel collar, the wheel then the other wheel collar but do

t tighten. Now position the

wheel

pant onto the axle and determine the exact position of the inner and outer wheel collars

such that

the tire will not rub against the wheel pant. Once you have this location add blue thread

lock to

the set screw and tighten your wheel collars. Now position the wheel pant(s) onto the

axle/gear

and secure with the 3mm bolts/washers and use blue thread lock on these as well.

Содержание ARF RC

















Результаты поиска

Содержание ARF RC

Отзывы:

Бренды по названию

Популярные бренды

Extreme Flight ARF RC, Инструкция по сборке

Результаты поиска

Содержание ARF RC

Отзывы:

Бренды по названию

Популярные бренды