Extreme Flight ARF RC Скачать руководство пользователя | Manualshive

Страница: 14 / 16

background image

10. Next we'll install the engine. There are laser marked locations to drill if using the DA-120. There is

also a laser scribed cross to use a template for other engine makes. Drill for 1/4x20 mounting bolts at the

proper locations.

11.

Install the DA-120 using the Blazing Star

one

inch mount with BOTH 2mm and 3mm Delrin spacer

provided

with the mount. Be sure the spacer goes between the mount and plywood firewall, not against the

engine. Secure

using 1/4x20 bolts, washers and lock nuts (not included). Total distance from the front of the

motor box to the

rear of the spinner backplate is 7 7/16" or 189mm.

«
...
12
13
14
15
16
»

Содержание ARF RC

















Отзывы:

Нет отзывов

Похожие инструкции для ARF RC

Бренд: RedWing RC Страницы: 20

Бренд: Viessmann Страницы: 2

Vac-U-Soling Lower Hull Kit

Бренд: Vac-U-Boat Страницы: 30

Fordhampton Garden center

Бренд: GAUGEMASTER Страницы: 4

Бренд: GAME OF BRICKS Страницы: 31

INDOOR SWIMMING-POOL WITH SLIDE

Бренд: Faller Страницы: 16

Бренд: Eduard Страницы: 10

Tribute EP 3D Profile

Бренд: E-FLITE Страницы: 40

Бренд: Tail Company Страницы: 4

Бренд: HobbyBoss Страницы: 16

Бренд: Fisher-Price Страницы: 10

SUPER CYCLONE COASTER 51957

Бренд: K'Nex Страницы: 48

Бренд: E-FLITE Страницы: 16

Бренд: Fisher-Price Страницы: 10

Circuit Explorer Rover

Бренд: Educational Insights Страницы: 28

Tap 'N Play Piano Mat

Бренд: Winfun Страницы: 12

Smart Start Future

Бренд: VTech Страницы: 16

Nano Warbirds P-47

Бренд: J-Power Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды