background image

106” Edge 540

 V2

 Assembly Manual 

Thank you for purchasing this 3DHobbyShop by Extreme Flight  ARF RC aircraft. If you have any 
issues, questions, concerns or problems during assembly, please contact our tech department at: 

[email protected]

 or 770-887-1794 10am-5pm Eastern Monday thru Friday.

Extreme Flight R

C

, Ltd. guarantees this kit to be free of defects in materials and workmanship for a 

period of 30 DA

Y

S from the date of purchase. All warranty claims must be accompanied by the original 

dated receipt. This warranty is extended to the original purchaser of the aircraft kit only. Extreme Flight 

R

in no way warranties its aircraft against flutter. We have put these aircraft through the most grueling 

flight tests imaginable and have not experienced any control surface flutter. Proper servo selection

 

and 

linkage set-up is absolutely essential. 

Ina

dequate servos or improper linkage set up may result in flutter 

and possibly the complete destruction of your aircraft. 

I

f you are not experienced in this type of linkage 

set-up or have questions regarding servo choices, please contact us at [email protected] or 

770-887-17

9

4. 

I

t is your responsibility to ensure the airworthiness of your model.

SAFETY in Assembly

During assembly of this aircraft, you will be asked to use sharp knives and hobby adhesives. 
Please follow all safety procedures recommended by the manufacturers of the products you use,
and always follow these important guidelines:
ALWAYS protect your eyes when working with adhesives, knives, or tools, especially power 
tools. Safety glasses are the best way to protect your eyes.
ALWAYS protect your body, especially your hands and fingers when using adhesives, knives, 
or tools, especially power tools. Do not cut toward exposed skin with hobby knives. Do not 
place hobby knives on tables or benches where they can roll off or be knocked off.
ALWAYS have a first-aid kit handy when working with adhesives, knives, or tools, especially 
power tools. ALWAYS keep hobby equipment and supplies out of the reach of children.

Содержание ARF RC

















Отзывы: