background image

13

ENGLISH

cHecks and Measures For coMMissioning

caution!

For correct generator operation, tHe Hydraulic systeM pressure Must be between 0.6 and 2,7 bar.

Whenever the pressure detected by the digital pressure switch is lower than 0.6 or over 2.7 bar, the boiler goes into alarm mode.

By taking the pressure of the water within standard values, the alarm can be reset by pressing the ON/1 key for 3 seconds

(The alarm can be reset only if the fumes motor has stopped and 15 minutes have passed since the alarm was displayed)

tHe pellet load Motor does not Function:

It is normal that there is air inside the circuit due to filling the system.

On the 1st ignition cycle, the movement of the water causes the air bubbles to move and be bled by the system automatic venting. This can 

cause the pressure to drop and the minimum pressure switch to intervene, which interrupts operation of the pellet conveying motor and 

therefore operation of the heat generator.

The system must be bled several times to eliminate the air and loaded when the pressure is too low.

It is not an anomaly, but normal phenomenon, due to filling. following filling, the system must always be bled using the relevant vents in the 

circuit and having the machine perform the "air vent" function.  (following commissioning and with the machine cold, activate the "air vent" 

function again. - see "

SETTINGS

" chapter)

bulb tHerMostats - rearM

Check by pressing rearm, before contacting a technician (see REARM chapter).

The diagram at the side illustrates the behaviour of the pump used 

on our thermo-products at the speeds that can be set.

flow rate (m

3

/h)

Head (m)

Features

Water content of the thermo-product heat exchanger (l)

18.5

volume of expansion vessel integrated into thermo-product (l)

*8

3 bar safety valve integrated into the thermo-product

YES

Minimum and maximum pressure switch integrated into the thermo-product

YES

PWM Pump integrated into the thermo-product

YES

Pump max. head (m)

6

ENvisiON aNy iNTEgraTivE ExpaNsiON vEssEl ON ThE Basis Of ThE sysTEm WaTEr cONTENT.

Содержание RAFFAELLA IDRO H15





































Отзывы: