Explo X2 Wave Flamer Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 62

background image

11

Status-LEDs of the X2 Wave Flamer

FULL

Shows that the pumping unit has reached usage pressure.

PUMP

Is only lit if the pump is working. Should only be lit in armed-mode.

ERR

This LED indicates any errors with the device. If lit, the fuel canister may be empty.

The Wave Flamer may not be used if this LED is lit, since it may lead to damages of
the device.

Please note the errorcode and contact the manufacturer.

RX

This LED flashes if a radio signal from the transmitter is received.

DMX

If DMX is integrated into the device, and is ready for use, this LED will be lit. If the
projector receives DMX signals, it will flash for confirmation.

BAT

Shows the status of the power supply. If it is lit permanently, the power is okay. If it
begins to flash, the device does not receive sufficient power. This may be caused by
a defunct mains supply.

ARMED

The three middle LEDs are lit if the device is in armed-mode. During this time, be
cautious when using the device, and make sure all safety distances are being
adhered to.

3.5.4 ANTENNA SOCKET

A fitting antenna with BNC connector can be mounted to the BNC antenna socket for radio use. We
recommend the use of original antennas.

The antenna is used to receive data. Pinching or breaking the antenna or its cable can lead to
damages, and should therefore be avoided. During use, make sure that the antenna is safely mounted
and placed upright, to guarantee the best possible radio reception.

Water or moisture entering the antenna socket can drastically decrease the radio reception.

3.5.5 PROGRAMMING SOCKET

Combined with the bootloader programming cable (sold separately) updates of the devices software
can be made by yourself.

3.5.6 DMX-CONNECTORS

Via the 3 pole XLR connectors, a DMX controller can be connected to the Wave Flame. The outgoing
socket can be used to forward the DMX signal to the next Wave Flamer.

Pin-configuration of the DMX-connector

Pin 1

GND

Pin 2

B

Pin 3

A

3.5.7 ON / OFF SW ITCH (POW ER)

Allows you to switch the Wave Flamers power supply on or off. After switching the wip switch on, the
key switch must be at least switched on shortly, to start up the device.

«
...
9
10
11
12
13
...
»

Содержание X2 Wave Flamer































































Отзывы:

Нет отзывов

Похожие инструкции для X2 Wave Flamer

Бренд: Labnet Страницы: 2

Бренд: Febco Страницы: 12

Бренд: Yetter Страницы: 16

Бренд: YardCraft Страницы: 17

Бренд: Obdstar Страницы: 10

Бренд: ACCU-CHECK Страницы: 104

Бренд: dbx Страницы: 2

Бренд: Eagle Group Страницы: 8

Бренд: Idex Страницы: 141

Бренд: IDEAL Networks Страницы: 8

Бренд: IDEAL Networks Страницы: 5

Бренд: Madsen Страницы: 206

Бренд: R&S Страницы: 371

Бренд: R.M. Young Страницы: 9

Бренд: UNIS Страницы: 16

Bathomatic Basic

Бренд: Unique Automation Страницы: 10

Бренд: Additel Страницы: 139

Бренд: Garden Treasures Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды