Expert Electronics ColibriDDC Скачать руководство пользователя страница 57

Страница: 57 / 69

ColibriDDC User Manual

ExpertSDR2 SOFTWARE DESCRIPTION

Password - Password.

Enter the password if the server requires it.

To transfer the IQ signal in the CW Skimmer you need to adjust the settings of the audio device

in the RX I Q out put category, it consists of:

Enable checkbox - Enable the IQ signal transfer from the EpertSDR2 to the CW Skimmer.

Driver – Audio device driver type.

Out put – Audio device physical output.

Channels – Amount of the used channels of the audio device.

Sample rat e – Sampling frequency.

Buf f er size – Buffer size.

Lat ency – Signal delay time.

Note:

If CW Skimmer is installed on the receiver's PC, then for the signal output you need to use
Virtual Audio Cable.

Sync f requency - set the Sync f requency to synchronize the CW Skimmer frequency with

ExpertSDR2 frequency.

Tune f requency f rom CW Skimmer - CW Skimmer set the ExpertSDR2 frequency. Set the

Tune f requency f rom CW Skimmer to tune the ExpertSDR2 frequency by the mouse click

on the station in the CW Skimmer.

3.3.9

Shortcuts menu

In the Short cut s menu, you can see the shortcut key combinations settings.

With the key combinations, you can control the receiver from your keyboard.

Note:

Shortcuts will be active only if the receiver's software window is in focus.

Содержание ColibriDDC






































































Результаты поиска

Содержание ColibriDDC

Отзывы:

Бренды по названию

Популярные бренды

Expert Electronics ColibriDDC, Руководство пользователя

Результаты поиска

Содержание ColibriDDC

Отзывы:

Бренды по названию

Популярные бренды