Expert Electronics ColibriDDC Скачать руководство пользователя страница 22

Страница: 22 / 69

ColibriDDC User Manual

ExpertSDR2 SOFTWARE DESCRIPTION

- Double Side Band

- Lower Side Band

- Upper Side Band

- CW mode. It works in CW-U for all bands. It cannot be changed.

- Narrow FM

- Wide FM, supports receiving of the stereo signals

- Spectrum mode. Receive the pure signal without any demodulation (panadapter

bandwidth). The idea is to receive pure signal then pass it to some special device, via a cable

connected to the PHONES audio output of the transceiver or PC audio output, with certain

demodulation capabilities

- Digital Lower Side Band. Connect a third-party software (is not supplied) to the

transceiver software for operating in digital modes

- Digital Upper Side Band. Connect a third-party software (is not supplied) to the

transceiver software for operating in digital modes

- Digital Radio Mondiale, 10 kHz filter with 5 kHz IF to work with the external decoder of

the DRM signals. Connect third-party software (is not supplied) to the transceiver software for

decoding of the DRM signals

160M - 2M - amateur bands

G EN - if out of the amateur bands

3.2.2

Frequency and S-meter indicators

Mainly, this panel consists of the visual indicators, like the VFO A/B frequencies, the signal level

on the antenna's input (S-meter) and several control buttons.

Displaying elements:

- VFO B frequency indicator (sub-receiver).

Note:

You won’t hear the audio from the VFO B if it is out of the panorama bandwidth.

Содержание ColibriDDC






































































Результаты поиска

Содержание ColibriDDC

Отзывы:

Бренды по названию

Популярные бренды

Expert Electronics ColibriDDC, Руководство пользователя

Результаты поиска

Содержание ColibriDDC

Отзывы:

Бренды по названию

Популярные бренды