background image

BACKUP

 

RELIEF

 

BELT

 

USER

 

MANUAL

 

 

Ver.

 

1.0

 

Unikia

 

AS

 

Sandakerveien

 

24c,

 

Bygg

 

c1,

 

0473

 

Oslo,

 

Norway

                                             

12

 

 

 

FCC

 

Caution

 

  This device complies with part 15 of the FCC Rules. Operation is subject to the following 

two conditions: (1) This device may not cause harmful interference, and (2) this device 

must accept any interference received, including interference that may cause undesired 

operation. 

 

Note:

 This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide 

reasonable protection against harmful interference in a residential installation. This 

equipment generates uses and can radiate radio frequency energy and, if not installed and 

used in accordance with the instructions, may cause harmful interference to radio 

communications. However, there is no guarantee that interference will not occur in a 

particular installation. If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the equipment off and on, the 

user is encouraged to try to correct the interference by one or more of the following 

measures: 

-Reorient or relocate the receiving antenna. 

-Increase the separation between the equipment and receiver. 

-Connect the equipment into an outlet on a circuit different from that to which the receiver 

is connected.Consult the dealer or an experienced radio/TV technician for help. 

 

 

Any Changes or modifications not expressly approved by the party responsible for 

compliance could void the user's authority to operate the equipment.

 

 

 

Содержание 002















Отзывы: