BACKUP
RELIEF
BELT
USER
MANUAL
Ver.
1.0
Unikia
AS
Sandakerveien
24c,
Bygg
c1,
0473
Oslo,
Norway
4
1.
Trim,
not
shave,
excessive
hair
on
the
treatment
area.
2.
Wash
the
skin
and
dry
completely
3.
Separate
the
two
gel
pads.
4.
Remove
the
film
with
reading
“ELECTRODE”
from
the
side
being
applied
to
the
electrode
area.
This
film
is
the
smallest
of
the
two.
Do
not
remove
the
protective
liner
on
the
“skin
side”
yet.
5.
Align
the
shape
of
the
first
gel
pad
with
the
electrode
area.
Apply
the
gel
pad
onto
the
electrode
area
and
firmly
press
across
the
entire
surface
to
ensure
good
adhesion.
6.
Repeat
steps
3
–
5
for
the
second
gel
pad.
HOW DOES IT WORK
Tens
treatment
works
in
two
ways.
It
stimulates
nerves
that
normally
carries
pain
signals
thus
“blocking”
these
(“closing
the
pain
gate”).
It
also
releases
endorphins
as
if
from
exercise,
endorphins
is
the
body`s
“natural
pain
killers”.
TREATMENT RECOMMENDATIONS
•
You
can
leave
the
device
in
position
for
multiple
treatments
during
the
day.
It
will
automatically
turn
Off
after
one
(1)
hour
of
treatment.
If
no
treatment
is
active
the
unit
will
turn
off
completely
after
15
minutes.
•
It
is
recommended
you
wait
a
minimum
of
30
minutes
between
treatments.
CONDUCTING A TENS TREATMENT
Always
read
the
safety
warnings
before
conducting
a
treatment.
Follow
these
steps
to
conduct
a
treatment:
1.
Remove
the
protective
liners
from
the
“skin
side”
of
the
gel
pads
by
slowly
peeling
the
liner
diagonally
from
an
inside
corner
to
the
opposite
outside
corner.
Important!
Avoid
contact
of
the
gel
pad
with
other
objects.
Contact
with
other
objects
may
affect
the
pads
adhesion
properties.
Save
the
liners
for
storage
of
the
device.
2.
Align
the
center
of
the
device
over
the
spine
and
place
the
device
on
your
back
in
the
area
of
pain.
If
you
cannot
place
the
device
properly,
ask
another
person
for
assistance.
Important!
Do
not
apply
the
gel
pads/electrodes
directly
over
the
spine.
3.
Press
the
On/Off
button
on
the
main
unit.
The
LED
will
flash
green
for
10
seconds
indicating
the
device
is
ready
for
use.
4.
Press
the
ON/OFF
button
on
the
remote.
Both
signal
lights
will
blink
twice
to
signal
remote
is
on.
Then
press
the
“+”
button
on
the
remote
control
to
begin
the
treatment.
The
TENS
signal
light
on
the
remote
will
blink
once
to
indicate
signal
is
sent
from
remote.
Note:
The
LED
on
the
main
unit
will
flash
blue
for
10
seconds
to
indicate
TENS
treatment
is
activated.
5.
Press
the
(+/
‐
)
buttons
to
increase
or
decrease
the
intensity
of
the
stimulation
until
it
is
at
a
comfortable
level.
There
are
4
levels.
6.
Press
the
ON/OFF
button
on
the
remote
control
to
stop
the
treatment
at
any
time.
Both
indicator
lights
will
blink
twice
to
signal
remote
is
off.
Treatment
will
automatically
stop
after
1
hour
of
inactivity
(not
pressing
any
buttons)
‐
Alternatively
press
the
“
‐
“
button
several
times
to
reduce
intensity
and
finally
turn
off
the
treatment.
