Exodraft EHC20 Скачать руководство пользователя страница 64

Страница: 64 / 72

• Menu sequence and structure

3110086 EHC20 UK 110515

6.8 Setup

Once launched, the setup wizard guides you through the basic settings for the setup in the correct order and provides

brief descriptions of the various parameters in the display.

Pressing the ”esc” button takes you back to the previous value so that you can view the selected setting again and

adjust it if necessary. Pressing the ”esc” button more than once takes you back to the selection mode, thus cancelling

the setup wizard. (See also ”F.2 Setup wizard”, page 44)

The setup wizard should only be launched by a specialist! Observe the explanations of the

individual parameters in this manual, and check whether further settings are necessary for

your application.

6.9 Factory settings

All settings can be reset to the original factory settings.

All controller parameters and statistics etc. will be irretrievably lost. The controller will then

need to be set up again.

6.10 SD card

Settings for the logging function with data storage on the SD card.

6.10.1 Logging

In this menu, you can enable the logging of sensor and relay data and adjust the settings. Various file formats are available.

Setting range: On, Off / default: Off

6.10.2 Free storage space

Shows the amount of free space available on the SD card.

6.10.3 Load configuration

This function allows you to load all controller settings from the SD card.

All previous controller settings will be overwritten.

6.10.4 Save configuration

This function allows you to save all controller settings including the service values on the SD card.

6.10.5 Firmware update

With this function, the firmware stored on the SD card will be transferred to the controller.

During the firmware update, do not switch off the controller or disconnect the power as this

can cause irreparable damage.
Settings can be changed and/or overwritten. After the firmware update, reset the controller to

the factory settings and carry out the setup procedure again.

6.10.6 Eject

In order to remove the SD card with no risk of damage or data loss, you should deregister it here first.

Содержание EHC20









































































Результаты поиска

Содержание EHC20

Отзывы:

Похожие инструкции для EHC20

Бренды по названию

Популярные бренды

Exodraft EHC20, Монтаж, установка и эксплуатация инструкция

Результаты поиска

Содержание EHC20

Отзывы:

Похожие инструкции для EHC20

Бренды по названию

Популярные бренды