Exmark LAZER Z LZS22KA484 Скачать руководство пользователя | Manualshive

Страница: 48 / 64

background image

Maintenance

Cleaning

Clean Engine and Exhaust
System Area

Service Interval: Before each use or daily

(May be required more
often in dry or dirty
conditions.)

CAUTION

Excessive debris around engine cooling air
intake and exhaust system area can cause engine,
exhaust area, and hydraulic system to overheat
which can create a fire hazard.

Clean all debris from engine and exhaust system
area.

1. Stop engine, wait for all moving parts to stop, and

remove key. Engage parking brake.

2. Clean all debris from rotating engine air intake

screen, around engine shrouding, and exhaust
system area.

3. Wipe up any excessive grease or oil around the

engine and exhaust system area

Remove Engine Shrouds and
Clean Cooling Fins

Service Interval: Every 100 hours

1. Stop engine, wait for all moving parts to stop, and

remove key. Engage parking brake.

2. Remove cooling shrouds from engine and clean

cooling fins. Also clean dust, dirt and oil from
external surfaces of engine which can cause
inadequate cooling.

3. Make sure cooling shrouds are reinstalled.

Operating the engine without cooling shrouds
will cause engine damage due to overheating.

Clean Hydro Fan Cooling
Fins

Service Interval: Before each use or daily

Removing debris from the hydro fan cooling fins will
allow the hydro system to run cooler and improve the
life of the hydro system.

1. Stop engine, wait for all moving parts to stop, and

remove key. Engage parking brake.

2. Slide seat all the way forward.

3. Remove accumulated debris from the hydro fan

cooling fins.

Clean Debris From Machine

Service Interval: Before each use or daily

1. Stop engine, wait for all moving parts to stop, and

remove key. Engage parking brake.

2. Clean off any oil, debris, or grass build-up on the

machine and cutting deck, especially under deck
belt shields, around the fuel tank, around engine
and exhaust area.

Clean Grass Build-Up Under
Deck

Service Interval: Before each use or daily

1. Stop engine, wait for all moving parts to stop, and

remove key. Engage parking brake.

2. Raise deck to the transport (5 1/2 inch (14 cm)

cutting height) position. Lift the front of unit
and support unit using jack stands or equivalent
support.

CAUTION

Raising the mower deck for service or
maintenance relying solely on mechanical
or hydraulic jacks could be dangerous. The
mechanical or hydraulic jacks may not be
enough support or may malfunction allowing
the unit to fall, which could cause injury.

Do Not rely solely on mechanical or hydraulic
jacks for support. Use adequate jack stands
or equivalent support.

3. Clean out any grass build-up from underside of

deck and in discharge deflector.

Waste Disposal

Motor Oil Disposal

Engine oil and hydraulic oil are both pollutants to
the environment. Dispose of used oil at a certified

48

«
...
46
47
48
49
50
...
»

Содержание LAZER Z LZS22KA484

































































Отзывы:

Нет отзывов

Похожие инструкции для LAZER Z LZS22KA484

Бренд: Elem Garden Technic Страницы: 58

LazerCut LCS405

Бренд: SANLI Страницы: 19

ZTR 5000 Series

Бренд: Dixon Страницы: 70

Бренд: Ransomes Страницы: 64

Бренд: Ariens Страницы: 32

Бренд: Parkside Страницы: 124

Smart Speed 569

Бренд: Troy-Bilt Страницы: 20

Бренд: Bad Boy Страницы: 36

Бренд: Electrolux Страницы: 13

Бренд: Electrolux Страницы: 16

Бренд: Electrolux Страницы: 12

Бренд: Electrolux Страницы: 35

Бренд: Electrolux Страницы: 9

Бренд: Electrolux Страницы: 61

Бренд: Electrolux Страницы: 84

Бренд: Electrolux Страницы: 10

Бренд: Cramer Страницы: 180

CRAFTSMAN 944.604060

Бренд: Sears Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды