Exmark LAZER Z LZS22KA484 Скачать руководство пользователя

Страница: 36 / 64

Maintenance

Figure 24

Full

Add

Note:

The oil level on the dipstick will be

incorrect if the oil is checked when the unit is hot.

7. If the dipstick oil level is at the “add” mark add

Exmark Premium Hydro Oil.

8. Replace hydraulic reservoir cap and tighten until

snug.

Do Not overtighten.

Check Tire Pressures

Service Interval: Every 50 hours

1. Stop engine, wait for all moving parts to stop, and

remove key. Engage parking brake.

2. Check tire pressure in drive tires.

3. Inflate drive tires to 13 psi (90 kPa).

4. Semi-pneumatic caster tires Do Not need to be

inflated.

Note:

Do Not add any type of tire liner or foam

fill material to the tires.

Excessive loads created by

foam filled tires may cause failures to the hydro drive
system, frame, and other components. Foam filling
tires will void the warranty.

Check Condition Of Belts

Service Interval: Every 50 hours

1. Stop engine, wait for all moving parts to stop, and

remove key. Engage parking brake.

2. Remove left and right belt shields on deck and lift

up floor pan to inspect deck drive belt.

3. Check under machine to inspect the pump drive

belt.

Note:

No adjustments are required for belt

tension.

Lubricate Grease Fittings

Note:

See chart for service intervals.

1. Stop engine, wait for all moving parts to stop, and

remove key. Engage parking brake.

2. Lubricate fittings with one to two pumps of

NGLI grade #2 multi-purpose gun grease.

Refer to the following chart for fitting locations
and lubrication schedule.

Lubrication Chart

Fitting

Locations

Initial

Pumps

Number of

Places

Service

Interval

1. Deck and
Pump Idler
Pivots

Yearly

2. Front
Caster
Pivots

*Yearly

* See step 3 for special lubrication instructions on
the front caster pivots.

3. Lubricate front caster pivots once a year. Remove

hex plug and cap. Thread grease zerk in hole and
pump with grease until it oozes out around top
bearing. Remove grease zerk and thread plug back
in. Place cap back on.

Lubricate Caster Wheel Hubs

Service Interval: As required

1. Stop engine, wait for all moving parts to stop, and

remove key. Engage parking brake.

Содержание LAZER Z LZS22KA484

































































Результаты поиска

Содержание LAZER Z LZS22KA484

Отзывы:

Похожие инструкции для LAZER Z LZS22KA484

Бренды по названию

Популярные бренды

Exmark LAZER Z LZS22KA484, Руководство оператора

Результаты поиска

Содержание LAZER Z LZS22KA484

Отзывы:

Похожие инструкции для LAZER Z LZS22KA484

Бренды по названию

Популярные бренды