manualshive.com logo in svg

Exmark LAZER Z LZS22KA484, Руководство оператора

Поделиться
Скачать
Exmark LAZER Z LZS22KA484 Скачать руководство пользователя страница 47

Maintenance

Figure 39

1.

Bolts

4.

Nuts

2.

Control lever

5.

Slotted holes

3.

Control arm shaft

2. Move the control lever to the next set of holes.

Secure the lever with the two bolts.

3. Repeat the adjustment for the opposite control

lever.

Adjusting the Tilt

The motion control levers can be tilted fore or aft for
maximum operator comfort.

1. Loosen the upper bolt holding the control lever

to the control arm shaft.

2. Loosen the lower bolt just enough to pivot the

control lever fore or aft Figure 39. Tighten both
bolts to secure the control in the new position.

3. Repeat the adjustment for the opposite control

lever.

Motion Control Full Forward
Tracking Adjustment

If the machine travels or pulls to one side when the
motion control levers are in the full forward position,
adjust the cover plates.

1. Loosen the screws on a cover plate (see Figure 40).

2. Slide the cover plate backward or forward to

adjust the travel of the lever and tighten the
screws.

3. Drive the machine and check the full forward

tracking.

4. Repeat steps 1 through 3 until desired tracking

is obtained.

Figure 40

RH Motion Control Shown

1.

Screw

3.

Motion control lever

2.

Cover plate

Caster Pivot Bearings
Pre-Load Adjustment

Remove dust cap from caster and tighten nyloc nut
until washers are flat and back off 1/4 of a turn
to properly set the pre-load on the bearings. If
disassembled, make sure the spring disc washers are
reinstalled as shown in Figure 41.

Figure 41

1.

Spring disc washers

47

Содержание LAZER Z LZS22KA484

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды