Exmark LAZER Z LZS22KA484 Скачать руководство пользователя | Manualshive

Страница: 10 / 64

background image

Safety

CAUTION

If the ignition is in the “ON” position there
is potential for sparks and engagement
of components. Sparks could cause an
explosion or moving parts could accidentally
engage causing personal injury.

Be sure ignition switch is in the “OFF”
position before charging the battery.

•

Keep all guards, shields and all safety devices in
place and in safe working condition.

•

Check all bolts frequently to maintain proper
tightness.

•

Frequently check for worn or deteriorating
components that could create a hazard.

WARNING

Removing standard original equipment parts,
or using non-Exmark replacement parts and
accessories may alter the warranty, traction, and
safety of the machine. Failure to use original
Exmark parts could cause serious injury or
death.

Replace all parts including, but not limited to,
tires, belts, and blades with original Exmark
parts.

WARNING

Hydraulic fluid escaping under pressure
can penetrate skin and cause injury. Fluid
accidentally injected into the skin must be
surgically removed within a few hours by a doctor
familiar with this form of injury or gangrene may
result.

•

If equipped, make sure all hydraulic fluid
hoses and lines are in good condition and all
hydraulic connections and fittings are tight
before applying pressure to hydraulic system.

•

Keep body and hands away from pinhole
leaks or nozzles that eject high pressure
hydraulic fluid.

•

Use cardboard or paper, not your hands, to
find hydraulic leaks.

•

Safely relieve all pressure in the hydraulic
system by placing the motion control levers
in neutral and shutting off the engine before
performing any work on the hydraulic system.

For Kohler EFI (Electronic Fuel Injection) Units:

WARNING

Fuel system components are under high
pressure. The use of improper components can
result in system failure, gasoline leakage and
possible explosion.

Use only approved fuel lines and fuel filters for
high pressure systems.

10

«
...
8
9
10
11
12
...
»

Содержание LAZER Z LZS22KA484

































































Отзывы:

Нет отзывов

Похожие инструкции для LAZER Z LZS22KA484

Jacobsen 744908A

Бренд: Textron Страницы: 34

532 43 41-99 Rev. 1

Бренд: McCulloch Страницы: 72

Бренд: Land Pride Страницы: 2

Бренд: Honda Страницы: 24

Бренд: AL-KO Страницы: 304

Бренд: Snapper Страницы: 24

Бренд: Snapper Страницы: 32

Бренд: KLIPPO Страницы: 60

Бренд: Eliet Страницы: 106

GRASS 1265 ZSBW

Бренд: Garland Страницы: 172

Бренд: Yard-Man Страницы: 16

Бренд: STEELE PRODUCTS Страницы: 23

Бренд: Ferris Страницы: 24

Бренд: Racing Страницы: 20

Flymo Micro Compact 300 Plus

Бренд: Electrolux Страницы: 12

Бренд: Cub Cadet Страницы: 36

Бренд: Surtek Страницы: 17

Бренд: Poulan Pro Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды