Exmark Frontrunner FR25KD Скачать руководство пользователя страница 10

Страница: 10 / 52

1.4.3

When feasible, avoid operating the equipment in wet grass.

WARNING

POTENTIAL HAZARD

♦

Operating a FrontRunner tractor without

an approved Exmark front mount
attachment increases the possibility of
forward tip over.

WHAT CAN HAPPEN

♦

Tip-over could cause serious injury or

death.

HOW TO AVOID THE HAZARD

♦

When operating a FrontRunner tractor

without an approved Exmark front mount
attachment, observe the following:

Limit operation to minimum required to
install a different front mount
attachment.

Minimize speed and use extreme
caution.

Only operate on a flat level surface.

Do not operate up or down a trailer
ramp.

Avoid sudden acceleration or
deceleration.

1.4.4 Use

EXTREME

caution when mowing and/or turning on slopes as loss of traction

and/or tip-over could occur. The operator is responsible for safe operation on
slopes.

DANGER

POTENTIAL HAZARD

♦

Mowing on wet grass or steep slopes can

cause sliding and loss of control.

WHAT CAN HAPPEN

♦

Wheels dropping over edges, ditches,

steep banks, or water can cause
rollovers, which may result in serious
injury, death or drowning.

HOW TO AVOID THE HAZARD

♦

Do not mow slopes when grass is wet.

♦

Do not mow near drop-offs or near water.

♦

Do not mow slopes greater than 15

degrees.

♦

Reduce speed and use extreme caution

on slopes.

♦

Avoid sudden turns or rapid speed

changes.

For Exmark Mower Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

Содержание Frontrunner FR25KD





















































Результаты поиска

Содержание Frontrunner FR25KD

Отзывы:

Похожие инструкции для Frontrunner FR25KD

Бренды по названию

Популярные бренды

Exmark Frontrunner FR25KD, Руководство оператора

Результаты поиска

Содержание Frontrunner FR25KD

Отзывы:

Похожие инструкции для Frontrunner FR25KD

Бренды по названию

Популярные бренды